In this study, titanium chips (TC) generated from industrial facilities was utilized as TiO2 support for hydrogenation of carbon dioxide (CO2) to methyl alcohol (CH3OH) over Cu-based catalysts. Nano-sized CuO and ZnO catalysts were deposited on TiO2 support using a co-precipitation (CP) method (CuO-ZnO/TiO2), where the thermal treatment of TC and the particle size of TiC2 are optimized on CO2 conversion under different reaction temperature and contact time. Direct hydrogenation of CO2 to CH3OH over CuO-ZnO/TiO2 catalysts was achieved and the maximum selectivity (22%) and yield (18.2%) of CH3OH were obtained in the range of reaction temperature 210-240 degrees C under the 30 bar. The selectivity was readily increased by increasing the flow rate, which does not affect much to the CO2 conversion and CH3OH yield.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1166/jnn.2016.12009 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
The Use of Graphite Micropowder in the Finish Turning of the Ti-6Al-4V Titanium Alloy Under Minimum Quantity Lubrication Conditions.
Materials (Basel)
December 2024
Department of Production Engineering, Mechanical Engineering Faculty, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin, Poland.
The use of the minimum quantity lubrication (MQL) method during machining leads to the reduced consumption of cooling and lubricating liquids, thus contributing to sustainable machining. To improve the properties of liquids used under MQL conditions, they are enriched with various types of micro- and nanoparticles. The purpose of this study was to investigate the effect of the addition of graphite micropowder (GMP) on tool life, cutting force components, and selected surface roughness parameters during the finish turning of the Ti-6Al-4V titanium alloy under MQL conditions.
View Article and Find Full Text PDFEffect of tube debonding on the enamel surface in vitro : Evaluation with optical coherence tomography.
J Orofac Orthop
November 2024
Department of Cariology, Endodontology and Periodontology, University of Leipzig, Liebigstr. 12, 04103, Leipzig, Germany.
Objective: In vitro evaluation of the morphology of the enamel surface before bonding metal tubes and after debonding using spectral domain optical coherence tomography (SD-OCT) and light microscopy.
Methods: In all, 40 extracted caries-free human molars without defects were selected and cleaned. The tooth surfaces were imaged by light microscopy and SD-OCT prior to the placement of metal tubes (Titanium Orthos; Ormco, Brea, CA, USA).
Machining Characteristics During Short Hole Drilling of Titanium Alloy Ti10V2Fe3Al.
Materials (Basel)
November 2024
Institute for Machine Tools, University of Stuttgart, Keplerstraße 7, 70174 Stuttgart, Germany.
The single-phase titanium ß-alloy Ti10V2Fe3Al (Ti-1023) has been widely used in the aerospace industry due to its unique mechanical properties, which include high fatigue strength and fracture toughness, as well as high corrosion resistance. On the other hand, these unique properties significantly hinder the cutting processes of this material, especially those characterized by a closed machining process area, such as drilling. This paper is devoted to the study of the short hole drilling process of the above-mentioned titanium alloy using direct measurements and numerical modeling.
View Article and Find Full Text PDFMicrostructure and Corrosion Resistance of 7075 Aluminium Alloy Composite Material Obtained from Chips in the High-Energy Ball Milling Process.
Materials (Basel)
October 2024
Department of Materials Science, Faculty of Mechanical Engineering and Aeronautics, Rzeszow University of Technology, al. Powstańców Warszawy 12, 35-959 Rzeszow, Poland.
The high-energy ball milling process was applied to fabricate a composite material from 7075 aluminium alloy milling chips, silicon carbide, and titanium dioxide powders. Raw materials were ground, and the obtained powders were cold pressed and sintered. It was demonstrated that this method can be used in the recycling of aluminium alloy scrap characterised by a high surface-to-volume ratio, and also that chemical removal of the oxide layer from chips is not necessary.
View Article and Find Full Text PDFFlexible SERS chips for rapid on-site detection of tricyclazole pesticide in agricultural products.
Mikrochim Acta
October 2024
Phenikaa University Nano Institute (PHENA), Phenikaa University, Hanoi, 12116, Vietnam.
A flexible, ultrasensitive, and practical SERS chip is presented based on a paper/f-TiO/Ag structure. The chip enhances the self-assembly of Ag nanoparticles on a cellulose fiber matrix, facilitated by smart functionalized TiO nanomaterials (f-TiO). This design enables superior detection of the hazardous pesticide tricyclazole (TCZ) on crops using an advanced, simple, and efficient analytical method.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!