The main purpose of this study consists in investigating the effects of h-BN addition on the sinterability of β-CaSiO3 (β-CS) bioceramics. β-CS bioceramics with different contents of h-BN were prepared at the sintering temperature ranging from 800°C to 1100°C. The results showed that h-BN can be successfully used as sintering additive by being oxidized to form low melting point B2O3 related glassy phase and enhanced the flexural strength by the formation of rod-like β-CS grains. β-CS bioceramics with 1wt% h-BN sintered at 1000°C revealed flexural strength and fracture toughness of 182.2MPa and 2.4MPam(1/2) respectively, which were much higher than that of pure β-CS bioceramics (30.2MPa, 0.53MPam(1/2)) fabricated in the same processing condition.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.jmbbm.2016.05.014 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
A preliminary study of cell-based bone tissue engineering into 3D-printed β-tricalcium phosphate scaffolds and polydioxanone membranes.
Sci Rep
December 2024
Department of Basic Sciences, Araçatuba Dental School, São Paulo State University - UNESP, Araçatuba, 16066-840, Brazil.
Treatment of complex craniofacial deformities is still a challenge for medicine and dentistry because few approach therapies are available on the market that allow rehabilitation using 3D-printed medical devices. Thus, this study aims to create a scaffold with a morphology that simulates bone tissue, able to create a favorable environment for the development and differentiation of osteogenic cells. Moreover, its association with Plenum Guide, through cell-based tissue engineering (ASCs) for guided bone regeneration in critical rat calvarial defects.
View Article and Find Full Text PDFObturation quality of bioceramic sealers with different obturation techniques: a micro-CT evaluation.
Sci Rep
December 2024
Dental University Hospital, King Saud University Medical City, King Saud University, Riyadh, Saudi Arabia.
This micro-computed tomography (micro-CT) analysis in vitro study was designed to compare void volume in root canal fillings performed using the single-cone (SC) technique and the continuous wave condensation (CWC) technique with bioceramic (BC) sealer. Forty human-extracted, single-rooted mandibular premolars were cleaned, shaped, and divided into two groups (n = 20) based on the obturation technique. In the first group, obturation was performed using the CWC technique with TotalFill HiFlow BC sealer.
View Article and Find Full Text PDFComparative Assessment of Push-Out Bond Strength and Dentinal Tubule Penetration of Different Calcium-Silicate-Based Endodontic Sealers.
Dent J (Basel)
December 2024
Faculty of Dentistry, Iuliu Hatieganu University of Medicine and Pharmacy, 400012 Cluj-Napoca, Romania.
Adhesion within endodontic obturation material and root canal walls improves the efficacy of the endodontic treatment by establishing a barrier that inhibits reinfection and entombs residual bacteria. This study evaluates the push-out bond strength (POBS) of calcium silicate sealers compared to an epoxy-resin-based sealer. A total of 36 extracted mono-radicular teeth were prepared with Pro Taper Ultimate and irrigated with 5.
View Article and Find Full Text PDFInvestigation of Antibiotic-Releasing Biodegradable Composite Bone Cements for Treating Experimental Chronic Maxillofacial Bone Infection.
J Biomed Mater Res A
January 2025
Department of Periodontics, Dr. R. Ahmed Dental College and Hospital, Kolkata, West Bengal, India.
Chronic osteomyelitis of the maxillofacial bones (i.e., jaw bones) is a persistent infection that requires effective treatment.
View Article and Find Full Text PDFOptimal parameter setting and evaluation for ultraviolet-assisted direct ink writing bioprinting of nHA/PEGDA scaffold.
Biomed Mater
December 2024
Department of Oral and Maxillofacial Surgery, First Hospital of Shanxi Medical University, Xinjian South Road 85#, Taiyuan, China, Taiyuan, 030001, CHINA.
Ultraviolet-assisted Direct Ink Writing（UV-DIW）, an extrusion-based additive manufacturing technology, has emerged as a prominent 3D printing technique and is currently an important topic in bone tissue engineering research. This study focused on the printability of double-network (DN) bioink (Nano-hydroxyapatite/Polyethylene glycol diacrylate(nHA/PEGDA)). Next, we search for the optimal UV-DIW printing parameters for the scaffold formed by nHA-PEGDA.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!