Objectives/hypothesis: To examine the effect of and predict the success of type 1 laryngeal cleft (LC-1) augmentation through swallowing evaluations.
Study Design: Retrospective chart analysis.
Methods: Sixty-eight patients with LC-1s underwent interarytenoid injection laryngoplasty (IL) and were examined. The median age at IL was 9 months. Swallowing evaluations were performed pre- and postoperatively using fiberoptic endoscopic examination of swallowing or modified barium swallow. The presence of aspiration or penetrations at various consistencies was recorded. McNemar's tests were used to detect changes in swallowing pre- and postoperatively. Logistic regression was used to assess factors affecting the odds of postoperative success.
Results: Preoperatively, 89.7% of patients demonstrated penetration or aspiration. Post-IL, 69.1% were safe for thins, and 75% showed improvement in swallowing. Postoperatively, there was a significant reduction in patients experiencing problems with thin liquids (P < 0.001) and in those with frank or silent aspiration (P < 0.001). Patients with penetrations on thin liquids had higher likelihood of a successful IL (odds ratio [OR] = 3.68, P = 0.021). The probability of success with silent aspiration at any consistency was significantly decreased (OR = 0.26, P = 0.015). Fifteen patients underwent formal endoscopic surgical repair, and 90.0% were safe with thin consistencies postoperatively.
Conclusion: A large proportion of patients with LC-1 and associated swallowing dysfunctions respond favorably to IL and formal repair. Children who demonstrated penetration with thin liquids had a higher rate of swallowing dysfunction resolution post-IL; whereas patients demonstrating silent aspiration had poorer responses to IL.
Level Of Evidence: 4. Laryngoscope, 126:2838-2843, 2016.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1002/lary.26069 | DOI Listing |
Nat Commun
January 2025
School of Environmental Science and Engineering, Sun Yat-sen University, Guangzhou, China.
Thin-film composite polyamide (TFC PA) membranes hold promise for energy-efficient liquid separation, but achieving high permeance and precise separation membrane via a facile approach that is compatible with present manufacturing line remains a great challenge. Herein, we demonstrate the use of lignin alkali (LA) derived from waste of paper pulp as an aqueous phase additive to regulate interfacial polymerization (IP) process for achieving high performance nanofiltration (NF) membrane. Various characterizations and molecular dynamics simulations revealed that LA can promote the diffusion and partition of aqueous phase monomer piperazine (PIP) molecules into organic phase and their uniform dispersion on substrate, accelerating the IP reaction and promoting greater interfacial instabilities, thus endowing formation of TFC NF membrane with an ultrathin, highly cross-linked, and crumpled PA layer.
View Article and Find Full Text PDFMater Horiz
January 2025
School of Materials Science and Engineering, Peking University, Beijing 1008711, P. R. China.
Intelligent soft robots that integrate both structural color and controllable actuation ability have attracted substantial attention for constructing biomimetic systems, biomedical devices, and soft robotics. However, simultaneously endowing single-layer cholesteric liquid crystal elastomer (CLCE) soft actuators with reversible 3D deformability and vivid structural color changes is still challenging. Herein, a multi-responsive (force, heat and light) single-layer 3D deformable soft actuator with vivid structural color-changing ability is realized through the reduced graphene oxide (RGO) deposition-induced Janus structure of the CLCE using a precisely-controlled evaporation method.
View Article and Find Full Text PDFSoft Matter
January 2025
Department of Mechanical and Aerospace Engineering, University at Buffalo, Buffalo, NY 14260, USA.
Monolayer assembly of charged colloidal particles at liquid interfaces opens a new avenue for advancing the additive manufacturing of thin film materials and devices with tailored properties. In this study, we investigated the dynamics of electrosprayed colloidal particles at curved droplet interfaces through a combination of physics-based computational simulations and machine learning. We employed a novel mesh-constrained Brownian dynamics (BD) algorithm coupled with Ansys® electric field simulations to model the transport and assembly of charged particles on a non-spherical droplet surface.
View Article and Find Full Text PDFACS Appl Eng Mater
December 2024
Department of Chemistry and Biochemistry, Rowan University, Glassboro, New Jersey 08028, United States.
Carbon-based nanofibers are critical materials with broad applications in industries such as energy, filtration, and biomedical devices. Polyacrylonitrile (PAN) is a primary precursor for carbon nanofibers, but conventional electrospinning techniques typically operate at low production rates of 0.1-1 mL/h from a single spinneret, limiting scalability.
View Article and Find Full Text PDFSpectrochim Acta A Mol Biomol Spectrosc
December 2024
Department of Chemistry, KTH Royal Institute of Technology, Teknikringen 29, SE-100 44 Stockholm, Sweden. Electronic address:
Nano-FTIR spectroscopy is a technique where atomic force microscopy (AFM) and infrared (IR) spectroscopy are combined to obtain chemical information with a lateral resolution of some tens of nm. It has been used to study numerous solid surfaces and recently also liquids including water have been examined by separating the liquid from the AFM tip by a thin lid. However, although the water stretching vibrations are significantly more intense than the bending vibration in conventional IR spectroscopy, only the bending vibration has been observed in nano-FTIR spectroscopy so far.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!