A method was established to simultaneously determine cadmium, iron and tin in canned-food samples using high-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GF AAS). The quantification step has been performed using the primary line (228.802nm) for cadmium and the adjacent secondary lines (228.725nm and 228.668nm) for iron and tin, respectively. The selected chemical modifier was an acid solution that contained a mixture of 0.1% (w/v) Pd and 0.05% (w/v) Mg. The absorbance signals were measured based on the peak area using 3 pixels for cadmium and 5 pixels for iron and tin. Under these conditions, cadmium, iron and tin have been determined in canned-food samples using the external calibration technique based on aqueous standards, where the limits of quantification were 2.10ngg(-1) for cadmium, 1.95mgkg(-1) for iron and 3.00mgkg(-1) for tin, and the characteristic masses were 1.0pg for cadmium, 0.9ng for iron and 1.1ng for tin. The precision was evaluated using two solutions of each metal ion, and the results, which were expressed as the relative standard deviation (RSD%), were 3.4-6.8%. The method accuracy for cadmium and iron was confirmed by analyzing a certified reference material of apple leaves (NIST 1515), which was supplied by NIST. However, for tin, the accuracy was confirmed by comparing the results of the proposed method and another analytical technique (inductively coupled plasma optical emission spectrometry). The proposed procedure was applied to determine cadmium, iron and tin in canned samples of peeled tomato and sardine. Eleven samples were analyzed, and the analyte concentrations were 3.57-62.9ngg(-1), 2.68-31.48mgkg(-1) and 4.06-122.0mgkg(-1) for cadmium, iron and tin, respectively. In all analyzed samples, the cadmium and tin contents were lower than the permissible maximum levels for these metals in canned foods in the Brazilian legislation.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.talanta.2016.02.023 | DOI Listing |
Microb Pathog
December 2024
Department of Biology, Faculty of Science, Arak University, Arak, 38156-8-8349, Iran.
Sci Rep
December 2024
Department of Computer Engineering, Marwadi University, Rajkot, 360003, India.
The contributed absorber design in graphene addition with the displacement of three materials for resonator design in Aluminum (Al), the middle substrate position with Titanium nitride (TiN), and the ground layer deposition by Iron (Fe) respectively. For the absorption validation highlight, the best four absorption wavelengths (µm) of 0.29, 0.
View Article and Find Full Text PDFHeliyon
November 2024
Department of Environmental Science, Baylor University, Waco, TX 76798-7266, USA.
J Colloid Interface Sci
November 2024
School of Chemistry and Chemical Engineering, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013, China. Electronic address:
Controlled synthesis of hierarchical flowerlike cobalt tin sulfide (SnCoS) is successfully obtained using the chelation of the biomolecule l-asparagine with cobalt-tin metal cations by a hydrothermal technique. l-asparagine plays a crucial role as an inducer and a good structure-directing activity. Subsequently, pine needle-shaped cobalt iron selenium (FeCoSe) is tightly deposited on the SnCoS surface to construct cobalt tin sulfide coated with cobalt iron selenide (FeCoSe@SnCoS) heterostructure, which has exposed more active sites and the most abundant channels for electron/ion transfer.
View Article and Find Full Text PDFJ Trace Elem Med Biol
November 2024
Toxicology Centre, University of Saskatchewan, Saskatoon, SK S7N 5B3, Canada.
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!