Background: Compressive osseointegration is a promising modality for limb salvage in distal femoral oncologic tumors. However, few studies have explored short-term survival rates in a large patient cohort of distal femur compressive endoprostheses or highlighted the risk factors for spindle failures.

Questions/purposes: We asked: (1) What is the frequency of compressive osseointegration spindle failure in distal femoral reconstructions? (2) What are the characteristics of rotational failure cases with distal femur compressive osseointegration endoprostheses? (3) What are the risk factors for mechanical and rotational failure of distal femur compressive osseointegration implantation? (4) What are other modalities of failure or causes of revision surgery, which affect patients undergoing distal femur compressive osseointegration implantation for oncologic reconstruction?

Methods: Between 1996 and 2013, 127 distal femoral reconstructions with the Compress(®) prosthesis were performed in 121 patients. During that time, 116 Compress(®) prostheses were implanted for aggressive primary tumors of the distal femur and/or failure of previous oncologic reconstruction. This approach represented approximately 91% of the distal femoral reconstructions performed during that time. Of the patients with prostheses implanted, four patients (four of 116, 3%) had died, and 37 (37 of 116, 32%) were lost to followup before 24 months. The median followup was 84 months (range, 24-198 months), and 71 patients (66% of all patients) were seen within the last 3 years. A retrospective chart review was performed to determine failure modality as defined by radiographs, clinical history, and intraoperative findings. Risk factors including age, sex, BMI, resection length, and perioperative chemotherapy were analyzed to determine effect on spindle and rotational failure rates. Survival analysis was determined using the Kaplan-Meier estimator. Differences in survival between groups were analyzed using the log rank test. Risk factors were determined using Cox proportional hazard modeling.

Results: Spindle survival at 5 and 10 years was 91% (95% CI, 82%-95%). Survival rates from rotational failure at 5 and 10 years were 92% (95% CI, 83%-96%); the majority of failures occurred within the first 2 years postoperatively and were the result of a twisting mechanism of injury. With the numbers available, none of the potential risk factors examined were associated with mechanical failure. The 5-year and 10-year all-cause revision-free survival rates were 57% (95% CI, 44%-67%) and 50% (95% CI, 36%-61%), respectively.

Conclusions: Distal femur compressive osseointegration is a viable method for endoprosthetic reconstruction. Rotational failure is rare with the majority occurring early. No variables were found to correlate with increased risk of mechanical failure. More research is needed to evaluate methods of preventing mechanical and rotational failures in addition to other common causes of revision such as infection in these massive endoprosthetic reconstructions.

Level Of Evidence: Level IV, therapeutic study.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC4887378PMC
http://dx.doi.org/10.1007/s11999-016-4839-7DOI Listing

Publication Analysis

Top Keywords

compressive osseointegration
28
distal femur
24
femur compressive
20
risk factors
20
rotational failure
20
distal femoral
16
survival rates
12
failure
11
distal
10
spindle failure
8

Similar Publications

Design, characterisation, and clinical evaluation of a novel porous Ti-6Al-4V hemipelvic prosthesis based on Voronoi diagram.

Biomater Transl

September 2024

Orthopaedic Research Institute and Department of Orthopaedics, West China Hospital, Sichuan University, Chengdu, Sichuan Province, China.

Three-dimensional printed Ti-6Al-4V hemipelvic prosthesis has become a current popular method for pelvic defect reconstruction. This paper presents a novel biomimetic hemipelvic prosthesis design that utilises patient-specific anatomical data in conjunction with the Voronoi diagram algorithm. Unlike traditional design methods that rely on fixed, homogeneous unit cell, the Voronoi diagram enables to create imitation of trabecular structure (ITS).

View Article and Find Full Text PDF

Nanograin enhanced surface layer strengthening of 3D printed intervertebral cage induced by sandblasting.

Biomed Mater

December 2024

Department of Orthopaedics, Fourth Military Medical University, No.1 Xinsi Road, Baqiao District, Xi'an, Shaanxi, 710032, CHINA.

3D printed customized titanium alloy (Ti6Al4V, TC4) as load-bearing prostheses and implants, such as intervertebral cage, were widely used in clinical practice. Natively biological inertia and inadequate bone in-growth of porous titanium alloy scaffolds hampered their clinically application efficiency and then extended healing period. To improve osseointegration capacity of 3D printed intervertebral cage, sandblasting was selected to execute their surface treatment.

View Article and Find Full Text PDF

Measurement of bone deformation and insertion torque during dental implant installation.

Oral Maxillofac Surg

December 2024

Instituto Militar de Engenharia, Praça General Tibúrcio 80, Urca, Rio de Janeiro, 22290-270, Brazil.

Aim: Insertion of dental implants causes bone deformation and induces residual bone compression stress, which can lead to implant failure if the bone loss threshold is exceeded. The current literature about bone stress is restricted to computer simulations and implant primary stability measurements after installation. This work measures the torque and deformation during implant insertion testing.

View Article and Find Full Text PDF

Mg alloy is one of the most suitable biodegradable materials for making modern LCP. This is due to the osseointegration property, low elastic modulus, the presence in the human bone, and the excellent biodegradable nature. But it lacks much-needed strength compared to conventional (Ti, SS alloys) implants due to low strength of biodegradable (Mg, Zn alloys) materials.

View Article and Find Full Text PDF

In recent years, additively manufactured metallic scaffolds have generated significant interest among researchers working in the field of bone tissue engineering and orthopaedic implants. Although such intricate, porous architectures are promising as bone substitutes, they need to be thoroughly tested for structural robustness as well as their capacity for bony integration. In this present work, we introduced and preclinically evaluated the biomechanical viability of Weaire-Phelan (WP) Ti-alloy scaffolds as bone replacement components.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!