Objective: This study aimed to measure the influence of drill length and irrigation system on heat production during osteotomy preparation for dental implants using bovine bone rib as experimental model.
Materials And Methods: Three groups were created: Group 1: drilling with three consecutive burs with double irrigation (internal and external) for a 4.0 mm conical implant; and Group 2 and Group 3: drilling with three consecutive burs with external irrigation for a 4.1 mm cylindrical implant and for a 4.3 mm conical implant, respectively. Four lengths were tested: 10, 12, 14 and 16 mm; in site prepared on bovine ribs using a surgical unit linked to a testing device, to standardize and simulate implant drilling procedures. Bone temperature variations were recorded using three thermocouples in different positions as of the crestal bone: 2 mm, position (p1); 7 mm, position 2 (p2); and 12 mm, position 3 (p3).
Results: The highest temperature changes were invariably recorded during the process of withdrawal. Significantly lower temperature changes (P < 0.02) could be recorded at maximum drilling depths during the shearing process regardless of drilling depth or irrigation method. Double irrigation was associated with significantly lower temperatures compared with external irrigation by the use of implant drills (P < 0.01).
Conclusions: Within the limitations of this ex vivo study was possible concluded that the use a double irrigation system in multiple conventional drill for osteotomy can decrease the heat generation when increase the drill length.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/clr.12827 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Burying poultry carcasses on farms as a disposal option in crisis situations: learnings and perspectives from a field study during an avian influenza epizootic in France.
Poult Sci
January 2025
Ploufragan-Plouzané-Niort Laboratory, Epidemiology Health and Welfare Unit, French Agency for Food, Environmental and Occupational Health and Safety (ANSES), BP53 22440 Ploufragan, France. Electronic address:
Appropriate disposal of dead farming animals is required to guarantee effective disease control while protecting the environment. In crisis situations, alternatives to rendering can be used, including on-farm burial. The objectives of this study were to: (i) describe the burial and monitoring protocols used on poultry farms in France in response to major avian influenza outbreaks; (ii) assess the effectiveness of the burial protocol, in terms of both technical and biosecurity aspects, and microbiological, physical and chemical changes of the buried materials and the environment over time; (iii) provide recommendations for future burial and follow-up protocols.
View Article and Find Full Text PDFPure CO and impure CO-SO-NO-O reactions with carbon storage site underlying seals: Coaly mudstones and carbonate cemented sandstones.
Sci Total Environ
January 2025
School of the Environment, University of Queensland, QLD, Australia.
The transition to net zero emissions requires the capture of carbon dioxide from industrial point sources, and direct air capture (DAC) from the atmosphere for geological storage. Dissolved CO has reactivity to rock core, and while the majority of previous studies have concentrated on reservoir rock or cap-rock reactivity, the underlying seal formation may also react with CO. Drill core from the underlying seal of a target CO storage site was reacted at in situ conditions with pure CO, and compared with an impure CO stream with SO, NO and O that could be expected from hard to abate industries.
View Article and Find Full Text PDFGuide-wire and K-wire readjustment jig for osteotomy and osteosynthesis: An instrument.
J Clin Orthop Trauma
February 2025
Joints and Spine Clinic, Mahavir Nagar, Kandivali West, Mumbai, 400067, India.
Introduction: Numerous orthopaedic procedures including dynamic hip screw plating and various osteotomies require placement of a reference guide pin or K wire to direct bone cuts or for drilling screw holes. Appropriate positioning of these wires is a critical component of surgery. Irrespective of whether one is a seasoned surgeon or an apprentice, these wires often need repositioning and readjustment.
View Article and Find Full Text PDFEngineering geological evaluation of Bowa Dayole dam site, North Shewa Zone, Oromia, Ethiopia.
Heliyon
January 2025
Department of Mining Engineering, College of Engineering, Addis Ababa Science and Technology University, Addis Ababa, P.O. Box: 16417, Ethiopia.
Developing nations like Ethiopia face food and water shortages due to weather and droughts. The Bowa Dayole masonry gravity dam is expected to irrigate farmland downstream. Despite this, the engineering geology is complicated by the presence of highly fractured and weathered aphanitic basaltic rock, along with a weak unwelded to welded tuff rock mass in the dam foundation.
View Article and Find Full Text PDFRemarkable improvement in drilling fluid properties with graphitic-carbon nitride for enhanced wellbore stability.
Heliyon
January 2025
Department of Chemical Engineering, School of Chemical and Materials Engineering (SCME), National University of Sciences & Technology (NUST), Sector H-12, Islamabad, 44000, Pakistan.
This study examines the viability of using graphitic-Carbon Nitride (g-CN) nanomaterial as shale stabilizer drilling fluid additive having applications in the oil and gas wells drilling. Shale stability is important especially when drilling horizontal and extended reach wells with water-based muds (WBM) to tap unconventional reservoirs namely shale oil and shale gas. For this study, the g-CN nanomaterial was produced by melamine pyrolysis, and characterized by X-Ray Diffraction, Scanning Electron Microscopy and Fourier Transform Infrared spectroscopy techniques.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!