We investigate guidance of Terahertz (THz) radiation in metallic and 3D-printed dielectric helical waveguides in the frequency range from 0.2 to 1 THz. Our experimental results obtained from THz time-domain spectroscopy (THz-TDS) measurements are in very good agreement with finite-difference time-domain (FDTD) simulations. We observe single-mode, low loss and low dispersive propagation of THz radiation in metallic helical waveguides over a broad bandwidth. The 3D-printed dielectric helical waveguides have substantially extended the bandwidth of a low loss dielectric tube waveguide as observed from the experimental and simulation results. The high flexibility of the helical design allows an easy incorporation into bench top THz devices.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1364/OE.23.033359 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Fully 3D-Printed Soft Capacitive Sensor of High Toughness and Large Measurement Range.
Adv Sci (Weinh)
January 2025
School of Science and Engineering, The Chinese University of Hong Kong, Shenzhen, 518172, P. R. China.
Soft capacitive sensors are widely utilized in wearable devices, flexible electronics, and soft robotics due to their high sensitivity. However, they may suffer delamination and/or debonding due to their low interfacial toughness. In addition, they usually exhibit a small measurement range resulting from their limited stiffness variation range.
View Article and Find Full Text PDF3D-printed aberration-free terahertz metalens for ultra-broadband achromatic super-resolution wide-angle imaging with high numerical aperture.
Nat Commun
January 2025
State Key Laboratory of Terahertz and Millimeter Waves, City University of Hong Kong, Hong Kong, 999077, China.
Terahertz (THz) lens constitutes a vital component in the THz system. Metasurfaces-based THz metalenses and classical bulky lenses are severely constrained by chromatic/ spherical aberration and the diffraction limit. Consequently, achromatic super-resolution THz lenses are urgently needed.
View Article and Find Full Text PDFFrom Dielectric to Electro-Responsive Thermoplastics: An Approach Based on Electro-Thermal Reorientation and Charged Gas Activation.
ACS Appl Polym Mater
December 2024
IMEM-BRT Group, Departament d'Enginyeria Química, EEBE, Universitat Politécnica de Catalunya, C/Eduard Maristany, 10-14, 08019 Barcelona, Spain.
The transition from insulator to electro-responsive has been successfully achieved by earlier studies for some inorganic materials by applying external stimuli that modify their 3D and/or electronic structures. In the case of insulating polymers, this transition is frequently accomplished by mixing them with other electroactive materials, even though a few physical treatments that induce suitable chemical modifications have also been reported. In this work, a smart approach based on the application of an electro-thermal reorientation process followed by a charged gas activation treatment has been developed for transforming insulating 3D printed polymers into electro-responsive materials.
View Article and Find Full Text PDF3D-Printed Electrohydrodynamic Pump and Development of Anti-Swelling Organohydrogel for Soft Robotics.
Adv Mater
January 2025
School of Materials Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, Singapore, 639798, Singapore.
Article Synopsis
- The study showcases improvements in electrohydrodynamic (EHD) pumps alongside a new 3D-printable organohydrogel designed for soft robotics.
- Using advanced digital light processing (DLP) technology, the researchers created a manifold pump array that can generate 90.2 kPa of pressure and deliver a flow rate of 800 mL per minute, far exceeding the capabilities of traditional EHD systems.
- The novel organohydrogel developed has a low swelling ratio, high stretchability, and durability under stress, making it ideal for dynamic applications in soft robotics, bioengineering, and vertical farming.
Low-Cost and Affordable Thermistor-Based Wideband Sub-THz Detector with Dielectric Waveguide Coupling.
Sensors (Basel)
November 2024
Institute of Optoelectronics, Military University of Technology, 2 Kaliski Street, 00-908 Warsaw, Poland.
Bolometric detection of electromagnetic radiation is a well-established method in a wide frequency range, from millimeter waves through the terahertz region up to infrared. Fabrication of such a detector is often an expensive and demanding process. We propose a simple device based on a commercially available thermistor as a sensing element.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!