Unlabelled: Thermal curing of the styrene-functionalized 9,9-diarylfluorene-based triaryldiamine monomer (VB-DAAF) forms an ideal p-type organic electrode interlayer capable of resisting solvation of the polar precursor solution in fabricating methylammonium lead iodide (CH3NH3PbI3) perovskite/fullerene (C60) planar heterojunction hybrid solar cells. The polymerized VB-DAAF film exhibits a good energy level alignment with the valence-band-edge level of the CH3NH3PbI3 perovskite to facilitate the transport of holes. The large energy barrier to the conduction-band-edge level of the CH3NH3PbI3 perovskite effectively blocks electrons from reaching the positive electrode and reduces the photon energy loss due to recombination. The best-performing cell with the configuration of glass/indium-tin oxide/polymerized VB-DAAF/CH3NH3PbI3 perovskite/C60/bathocuproine/aluminum is free of a poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (
Pedot: PSS) layer to achieve an open-circuit voltage (VOC) = 1.02 V, a short-circuit current (JSC) = 18.92 mA/cm(2), and a fill factor (FF) = 0.78, corresponding to a power conversion efficiency (PCE) of 15.17% under standard 1 sun AM 1.5G simulated solar irradiation. The performance is much superior to the device applying the
Pedot: PSS interlayer with photovoltaic parameters of VOC = 0.85 V, JSC = 16.37 mA/cm(2), and FF = 0.74, corresponding to a PCE of 10.27%. Additionally, we had applied a UV-assisted process to polymerize the VB-DAAF film at relatively lower temperature and fabricate decent perovskite-based solar cells on the flexible substrate for real applications.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1021/acsami.5b09012 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Electrodeposition of Nanostructured Metals on n-Silicon and Insights into Rhodium Deposition.
Nanomaterials (Basel)
December 2024
Dipartimento di Chimica "Ugo Schiff", Università degli Studi di Firenze, Via della Lastruccia 3, 50019 Sesto Fiorentino, Italy.
In this study, we investigate the electrodeposition of various metals on silicon. Mn, Co, Ni, Ru, Pd, Rh, and Pt were identified as promising candidates for controlled electrodeposition onto silicon. Electrochemical evaluations employing cyclic voltammetry, Scanning Electron Microscopy (SEM) associated with energy-dispersive X-Ray Spectroscopy (SEM-EDS), and X-Ray Photoelectron Spectroscopy (XPS) techniques confirmed the deposition of Pd, Rh, and Pt as nanoparticles.
View Article and Find Full Text PDFStudy of Thermalization Mechanisms of Hot Carriers in BABr-Added MAPbBr for the Top Layer of Four-Junction Solar Cells.
Nanomaterials (Basel)
December 2024
School of Photovoltaic and Renewable Energy Engineering, University of New South Wales, Kensington, NSW 2052, Australia.
The hot carrier multi-junction solar cell (HCMJC) is an advanced-concept solar cell with a theoretical efficiency greater than 65%. It combines the advantages of hot carrier solar cells and multi-junction solar cells with higher power conversion efficiency (PCE). The thermalization coefficient () has been shown to slow down by an order of magnitude in low-dimensional structures, which will significantly improve PCE.
View Article and Find Full Text PDFA Numerical Simulation Study of the Impact of Kesterites Hole Transport Materials in Quantum Dot-Sensitized Solar Cells Using SCAPS-1D.
Nanomaterials (Basel)
December 2024
Fort Hare Institute of Technology, University of Fort Hare, Private Bag X1314, Alice 5700, Eastern Cape, South Africa.
Energy generation and storage are critical challenges for developing economies due to rising populations and limited access to clean energy resources. Fossil fuels, commonly used for energy production, are costly and contribute to environmental pollution through greenhouse gas emissions. Quantum dot-sensitized solar cells (QDSSCs) offer a promising alternative due to their stability, low cost, and high-power conversion efficiency (PCE) compared to other third-generation solar cells.
View Article and Find Full Text PDFA Review of Transparent Conducting Films (TCFs): Prospective ITO and AZO Deposition Methods and Applications.
Nanomaterials (Basel)
December 2024
Division of Physics, Engineering, Mathematics and Computer Sciences and Optical Science Center for Applied Research, Delaware State University, Dover, DE 19901, USA.
This study offers a comprehensive summary of the current states as well as potential future directions of transparent conducting oxides (TCOs), particularly tin-doped indium oxide (ITO), the most readily accessible TCO on the market. Solar cells, flat panel displays (FPDs), liquid crystal displays (LCDs), antireflection (AR) coatings for airbus windows, photovoltaic and optoelectronic devices, transparent p-n junction diodes, etc. are a few of the best uses for this material.
View Article and Find Full Text PDFBithiophene Imide-Based Self-Assembled Monolayers (SAMs) on NiOx for High-Performance Tin Perovskite Solar Cells Fabricated Using a Two-Step Approach.
ACS Appl Mater Interfaces
December 2024
Department of Applied Chemistry and Institute of Molecular Science, National Yang Ming Chiao Tung University, 1001 Ta-Hseuh Road, Hsinchu 300093, Taiwan.
Three new bithiophene imide (BTI)-based organic small molecules, (), (), and (), with varied alkyl side chains, were developed and employed as self-assembled monolayers (SAMs) applied to NiOx films in tin perovskite solar cells (TPSCs). The NiOx layer has the effect of modifying the hydrophilicity and the surface roughness of ITO for SAM to uniformly deposit on it. The side chains of the SAM molecules play a vital role in the formation of a high-quality perovskite layer in TPSCs.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!