We present density functional theory based atomistic calculations predicting that slow fracturing of silicon is possible at any chosen crack propagation speed under suitable temperature and load conditions. We also present experiments demonstrating fracture propagation on the Si(110) cleavage plane in the ~100 m/s speed range, consistent with our predictions. These results suggest that many other brittle crystals could be broken arbitrarily slowly in controlled experiments.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1103/PhysRevLett.115.135501 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Shear localisation controls the dynamics of earthquakes.
Nat Commun
January 2025
Department of Earth Sciences, University College London, London, UK.
Earthquakes are produced by the propagation of rapid slip along tectonic faults. The propagation dynamics is governed by a balance between elastic stored energy in the surrounding rock, and dissipated energy at the propagating tip of the slipping patch. Energy dissipation is dictated by the mechanical behaviour of the fault, which is itself the result of feedbacks between thermo-hydro-mechanical processes acting at the mm to sub-mm scale.
View Article and Find Full Text PDFStudy on the crack propagation morphology and initiation law of coal rock under the action of underwater electric pulse.
Sci Rep
January 2025
School of Resources and Civil Engineering, Northeastern University, Shenyang, 110819, China.
Based on the symmetric initiation mechanism of double-wing cracks in coal rock mass induced by high-pressure electro-recoil water pressure, fracturing experiments have been performed on coal rock mass under different water pressures and discharge conditions using high-voltage electric pulse hydraulic fracturing devices. Combined with CT scans, the crack spatial distribution inside the post-break coal rock mass was analyzed and found that the edge of the water injection hole is prone to produce double-wing cracks along the drilling hole diameter. ABAQUS is used to verify the physical test and extend the test conditions, the geometric parameter change, morphological expansion rule and crack initiation mechanism of double-wing crack in coal rock mass under different discharge conditions and ground stress conditions are studied.
View Article and Find Full Text PDFFunctionally Graded Oxide Scale on (Hf,Zr,Ti)B Coating with Exceptional Ablation Resistance Induced by Unique Ti Dissolving.
Adv Sci (Weinh)
January 2025
Shaanxi Key Laboratory of Fiber Reinforced Light-Weight Composites, State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi'an, 710072, China.
Multicomponent Ti-containing ultra-high temperature ceramics (UHTCs) have emerged as more promising ablation-resistant materials than typical UHTCs for applications above 2000 °C. However, the underlying mechanism of Ti improving the ablation performance is still obscure. Here, (Hf,Zr,Ti)B coatings are fabricated by supersonic atmospheric plasma spraying, and the effects of Ti content on the ablation performance under an oxyacetylene flame are investigated.
View Article and Find Full Text PDFCarbon nanotubes at bilayer in-plane graphene/hBN with interlayer twist angles abnormally enhance its interlayer stress transfer.
iScience
January 2025
School of Civil Engineering and Architecture, Zhejiang University of Science & Technology, Hangzhou, P.R. China.
A possibility of unprecedented architecture may be opened up by combining both vertical and in-plane heterostructures. It is fascinating to discover that the interlayer stress transfer, interlayer binding energy, and interlayer shear stress of bi-layer Gr/hBN with CNTs heterostructures greatly increase (more than 2 times) with increase the numbers of CNTs and both saturate at the numbers of CNTs = 3, but it causes only 10.92% decrease in failure strain.
View Article and Find Full Text PDFPhysics-Based Synthetic Data Model for Automated Segmentation in Catalysis Microscopy.
Microsc Microanal
January 2025
Fritz-Haber-Institut der Max-Planck-Gesellschaft, Berlin 14195, Germany.
In catalysis research, the amount of microscopy data acquired when imaging dynamic processes is often too much for nonautomated quantitative analysis. Developing machine learned segmentation models is challenged by the requirement of high-quality annotated training data. We thus substitute expert-annotated data with a physics-based sequential synthetic data model.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!