Objective: This study investigated the surface roughness of enamel after debonding and instrumentation with commonly used methods.
Methods: Part I: a survey was sent to active members of the American Association of Orthodontists to determine popular bonding, debonding, and polishing protocols. Part II: brackets were bonded to the buccal surface of 30 extracted human premolar teeth. After debonding, residual adhesive was removed with 12-, 16-, and 20-fluted titanium carbide burs as based upon the survey results. The teeth were scanned with a surface profilometer for surface roughness. Part III: the teeth were further polished using a Reliance Renew polishing point or a prophy cup with pumice and rescanned for surface roughness.
Results: Part I: the majority of respondents used a generic bracket-removing plier to remove fixed appliances (53%) and a high-speed handpiece for adhesive removal (85%). The most popular bur was a 12-fluted carbide bur without water spray. The majority of respondents used pumice paste and/or Reliance Renew points after adhesive removal. Part II: there was a significant difference in enamel surface roughness when 12-, 16-, and 20-fluted carbide burs were compared via surface profilometry. Part III: further polishing with a Reliance Renew point or a prophy cup and pumice did not provide a significantly smoother surface.
Conclusions: The results show large variation in debonding and polishing techniques. Creating a smooth enamel surface is equally possible with 12- or 20-fluted carbide burs. Further polishing with pumice and prophy cup or Renew point does not provide an enamel smoother surface.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1179/1465313315Y.0000000009 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Development of chitosan-based films with invertase enzyme for active packaging: Physicochemical parameters, structure, application, and storage.
Int J Biol Macromol
January 2025
Department of Food Science, Federal University of Lavras (UFLA), Lavras 37200-000, Brazil.
The use of active packaging made from biodegradable polymers can contribute to the environment and to the food industry by increasing the shelf life of their products. This study aimed to produce chitosan-based films incorporated with the invertase enzyme (1, 2, 5, 9, and 10 %) as an alternative to avoid sucrose crystallization in the confectionery industry. The optimum activity of the invertase enzyme was observed at 55 °C and pH 5, thus, the films made with the film-forming solution adjusted to pH 5 and dried at 55 °C were compared with those without pH adjustment and dried at room temperature.
View Article and Find Full Text PDFSurface coating nanoarchitectonics for optimizing cytocompatibility and antimicrobial activity: The impact of hyaluronic acid positioning as the outermost layer.
Int J Biol Macromol
January 2025
Department of Chemistry, State University of Maringá, Maringá, PR, Brazil; Laboratory of Materials, Macromolecules, and Composites, Federal University of Technology - Paraná, Apucarana, PR, Brazil; National Institute for Materials Advancement, Pittsburg State University, Pittsburg, KS, USA; Department of Chemistry, Pittsburg State University, Pittsburg, KS, USA. Electronic address:
Polyelectrolyte multilayers (PEMs) based on hyaluronic acid (HA) and poly (diallyldimethylammonium chloride) (PDDA) were deposited on oxidized polystyrene (PS) via the layer-by-layer (LbL) method. The X-ray photoelectron spectroscopy (XPS) confirmed the PEM deposition on PS, and atomic force microscopy (AFM) indicated that the surface roughness of PS also increased after PEM deposition. The PEMs significantly enhanced PS wettability, reducing the contact angle from 73° on PS to 24° on PDDA-terminated (PDDA/HA) PEM (2.
View Article and Find Full Text PDFDesign of a Co doped carbon Backbone with self-grown Au nanoparticles via a 'Triple Advantage' Strategy for sensitive dopamine detection.
J Colloid Interface Sci
January 2025
State Key Laboratory of New Pharmaceutical Preparations and Excipients, Key Laboratory of Medicinal Chemistry and Molecular Diagnosis of the Ministry of Education, Key Laboratory of Analytical Science and Technology of Hebei Province, College of Chemistry and Materials Science, Hebei University 071002 Baoding, PR China. Electronic address:
In this study, a Co doped polyhedral carbon skeleton (Co CN) was prepared by nitrogen carbonization using ZIF-67 as a precursor. The Co CN features a rough surface with excellent electrical conductivity, and the Co atoms exhibit unique catalytic properties. Based on these characteristics, we used Co CN as a carrier to load Au nanoparticles (NPs) onto its surface through the linkage and reduction effects of polyoxometalates (POMs).
View Article and Find Full Text PDFPhysicochemical Properties of Curen® Filaments Versus Nylon Filaments in Toothbrush Bristles: An In Vitro Study.
Cureus
December 2024
Medical Affairs, Dr. Reddy's Laboratories Ltd., Hyderabad, IND.
Background Toothbrush manufacturers commonly use bristle materials such as nylon, polybutylene terephthalate, polypropylene, polyethylene terephthalate, boar hair, bamboo, carbon fiber, silicone, polylactic acid, or their modifications such as Curen. Nylon filaments have long been demonstrated to be durable and are widely used, but not much is known regarding the performance of Curen filaments compared to nylon filaments. This in vitro study compared the stiffness, abrasion potential, abrasion resistance, and bristle surface changes of Curen and nylon filaments.
View Article and Find Full Text PDFStudy on the effect of acid fracturing fluid on pore structure of middle to high rank coal.
Sci Rep
January 2025
College of Mining, Guizhou University, Guiyang, 550025, Guizhou, China.
Acid fracturing fluids can effectively improve the microporous structure of coal, thereby enhancing the permeability of coal seam and the efficiency of gas drainage. To explore the effects of acid fracturing fluids on the pore structure modification of coal samples from different coal ranks, hydrochloric acid-based acid fracturing fluids were prepared and used to soak four types of medium to high-rank coal in an experiment. High-pressure mercury intrusion and liquid nitrogen adsorption techniques results demonstrated that the acid fracturing fluid can effectively alter the pore structure of coal.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!