The retinal arterial network is the only source of the highly nutrient-consumptive retina, thus any insult on the arteries can impair the retinal oxygen and nutrient supply and affect its normal function. The aim of this work is to study the influences of vascular structure variation on the flow and pressure characteristics via microfluidic devices. Two sets of micro-channel were designed to mimic the stenosed microvessels and dichotomous branching structure in the retinal arteries. Three working fluids including red blood cell (RBC) suspension were employed to investigate the pressure drop in the stenosed channel. The flow behaviors of RBC suspensions inside the micro channels were observed using high speed camera system. Pressure drop of different working fluids and RBC velocity profiles in the stenosed channel were obtained. Moreover, hematocrit levels of RBC suspensions inside the bifurcated channels were analyzed from the sequential images of RBC flow. The results of the flow in the stenosed channel show that RBCs drift from the center of the channels, and RBC velocity is influenced not only by the inlet flow rate but also the interaction between RBCs. The measured pressure drops in the stenosed channel increase notably with the increase of fluid viscosity. Furthermore, the dimensionless pressure drop due to the stenosis decreases with Reynolds number. On the other hand, the results of flow through the bifurcated channels show that as the ratio of the daughter-branch width to the mother-channel width increases, the ratio of hematocrit in two connected branches (Ht/Hd) decreases, which is in favorable agreement with the available analysis results.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1007/s10544-015-9959-4 | DOI Listing |
Sci Rep
January 2025
Department of Mechanical Engineering, India KLS Vishwanathrao Deshpande Institute of Technology, Haliyal, India.
The current study assesses several water-based PVT system thermal absorber configurations. The thermal absorber in PVT system plays a vital role in efficiency evaluation as it lowers PV temperature and collects heat energy. The current study aims to discover and analyze advanced thermal absorber design by comparing well-received spiral circular absorbers and non-cooled PV with proposed semi-circular thermal absorbers with varying flow configurations.
View Article and Find Full Text PDFHepatology
January 2025
Department of Experimental and Clinical Medicine, University of Florence, Florence, Italy.
Background Aims: In clinical practice, the reduction of porto-caval pressure gradient (PCPG) following trans-jugular intra-hepatic porto-systemic shunt (TIPS) does not always meet the recommendation of current guidance. We evaluated the impact of different degrees of PCPG reduction, measured at the end of an elective TIPS, on ascites control, recurrence of portal hypertension-related bleeding (PHRB) and survival.
Approach And Results: Cirrhotic patients receiving TIPS for refractory ascites (RA) or for the secondary prophylaxis of PHRB were consecutively enrolled.
Sci Rep
January 2025
Production Technology Department, Faculty of Technology and Education, Beni-Suef University, Beni-Suef, 62521, Egypt.
Ball bearings face numerous challenges under harsh operating conditions of elevated pressure between the balls and other contacting parts of the bearing like drop in tribological properties. To address these challenges, this paper presents the first successful experimental investigation of incorporating an innovative hexagonal boron nitride (h-BN) into Aluminum-Carbon nanotube (Al-0.6 wt% CNTs) nanocomposites.
View Article and Find Full Text PDFSensors (Basel)
December 2024
MESA+ Institute for Nanotechnology, University of Twente, 7522 NH Enschede, The Netherlands.
This paper introduces a Coriolis mass flow and density sensor. The sensor is made using Surface Channel Technology (SCT) but with selective wet etching to create the channels. This method forms suspended microfluidic channels with a larger cross-sectional area.
View Article and Find Full Text PDFPharmaceutics
November 2024
Merck Life Science KGaA, Frankfurter Straße 250, 64293 Darmstadt, Germany.
Melt-based 3D printing technologies are currently extensively evaluated for research purposes as well as for industrial applications. Classical approaches often require intermediates, which can pose a risk to stability and add additional complexity to the process. The Advanced Melt Drop Deposition (AMDD) technology, is a 3D printing process that combines the principles of melt extrusion with pressure-driven ejection, similar to injection molding.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!