Workplace exposure to airborne Al2O3 nanoparticles in a pilot factory was characterised by particle concentrations, size distribution, morphology and chemical composition, compared with background particles. Real-time variations in number concentration (NC20-1000 nm), respirable mass concentration (MC100-1000 nm), active surface area concentration (SAC10-1000 nm) and particle size were measured at production locations involved in separation and packaging activities. Measurements during stable production periods showed significant increases in the various concentrations of agglomerated Al2O3 nanoparticles (about 305 nm) at separation locations, compared to those of background particles (p < 0.01). The size distribution model for separation processes might switch to primary nanoparticles (21-26 nm) during periods of unstable production. Packaging activities also caused significant increases in different concentrations of Al2O3 nanoparticles (about 90 nm) compared to background particles (p < 0.01). These particles exhibited a bimodal size distribution and floccus or cloudy-like agglomerates of primary nanoparticles. NC20-1000 nm and active SAC10-1000 nm variations showed the same trend, and were temporally consistent with particle emission scenarios or worker activities, but differed from that for respirable MC100-1000 nm. There was strong correlation between active SAC10-1000 nm and NC20-1000 nm (r = 0.823), moderate correlation between active SAC10-1000 nm and respirable MC100-1000 nm (r = 0.666) and relatively weak correlation between NC20-1000 nm and respirable MC100-1000 nm (r = 0.361). These findings from the pilot factory suggest significant exposure to Al2O3 nanoparticles or their agglomerates, associated with separation and packaging processes. The number and active surface area concentrations may be distinct from mass concentration and might be more appropriate for characterizing exposure to airborne nanoparticles.

Download full-text PDF

Source
http://dx.doi.org/10.1039/c4em00504jDOI Listing

Publication Analysis

Top Keywords

al2o3 nanoparticles
16
exposure airborne
12
separation packaging
12
pilot factory
12
size distribution
12
compared background
12
background particles
12
active sac10-1000
12
respirable mc100-1000
12
workplace exposure
8

Similar Publications

In this paper, alumina-modified wood liquefaction (AL-WP) was prepared by blending nano-alumina (AlO) into wood liquefaction phenolic resin (WP) using a co-blending method. Alumina-modified wood liquefaction protofilament fiber (AL-WPF) was obtained by melt-spinning, curing, and thermo-curing processes, which were followed by carbonization to obtain alumina-modified wood liquefaction carbon fiber (AL-WCF). This paper focuses on the enhancement effect of nano-alumina doping on the mechanical properties and heat resistance of wood liquefaction carbon fiber (WCF), explores the evolution of graphite microcrystalline structure during the high-temperature carbonization process, and optimizes the curing conditions of AL-WPF.

View Article and Find Full Text PDF

Experimental Investigation of Dispersant on Dynamics of Impact of AlO Nanofluid Droplet.

Nanomaterials (Basel)

January 2025

School of Aeronautical Engineering, Shandong Engineering Research Center of Aeronautical Materials and Devices, Shandong University of Aeronautics, Binzhou 256600, China.

Spray cooling, of which the essence is droplet impacting, is an efficient thermal management technique for dense electronic components in unmanned aerial vehicles (UAVs). Nanofluids are pointed as promising cooling dispersions. Since the nanofluids are unstable, a dispersant could be added to the fluid.

View Article and Find Full Text PDF

Nanoscale Fe(0)-zeolite composite derived from coal bottom ash for efficient treatment of Cr(VI)-contaminated groundwater: Unveiling the importance of locations for surface-bound Fe(II) and Fe(0) passivation products.

J Hazard Mater

January 2025

Department of Civil and Environmental Engineering, Konkuk University, 120 Neungdong-ro, Gwangjin-gu, Seoul 05029, Republic of Korea; Department of Environmental Engineering, Graduate School, Konkuk University, 120 Neungdong-ro, Gwangjin-gu, Seoul 05029, Republic of Korea. Electronic address:

The synthesis of coal bottom ash-induced zeolite (Si-Al material) has been widely reported; however, the selective recovery of the three main elements, viz., Si, Al, and Fe, from coal bottom ash for the synthesis of reactive adsorbents has not yet been reported. In this study, we separated the magnetic and non-magnetic fractions of coal bottom ash to selectively recover Fe and Si-Al for synthesizing nanoscale zero-valent iron@zeolite (NZVI@ZBA) composites with uniform formation of Fe(0) nanoparticles on the ZBA surface.

View Article and Find Full Text PDF

Isoelectric Point of Metal Oxide Films Formed by Anodization.

Langmuir

January 2025

Chemistry and Structure of novel Materials, University of Siegen, Paul-Bonatz Strasse 9-11, 57068 Siegen, Germany.

The surface charge of metal oxides is an important property that significantly contributes to a wide range of phenomena, including adsorption, catalysis, and material science. The surface charge can be predicted by determining the isoelectric point (IEP) of a material and the pH of a solution. Although there have been several studies of the IEP of metal oxide (nano)particles, only a few have reported the IEP of metal oxide films.

View Article and Find Full Text PDF

The anthocyanin-loaded films based on natural polymers as pH-responsive indicator are widely applied in the food preservation. However, the low mechanical strength and storage stability limited their practical application, there is an urgent demand to improve the performance of anthocyanin-loaded films. In order to avoid affecting the color indication of anthocyanins, we explored the effect of eight kinds of white nanomaterials on improving the performance of films.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!