The objective of the present research work was to isolate, purify and characterize Cordia dichotoma gum and investigate its disintegration property in oral tablets. The isolated gum was tested for physicochemical characteristics such as solubility, pH (1% w/w in water), swelling index, loss on drying, ash value, bulk and tapped density, Carr's index, Hausner's ratio and angle of repose. The Orodispersible tablets of valsartan were prepared by direct compression method and evaluated for average weight (mg), drug content (%), thickness (mm), hardness (kg/cm(2)), friability (%), wetting time (sec), water absorption ratio (%) and disintegration time (sec). FTIR studies revealed that there was no interaction between drug, gum and other excipients used in the study. The F4 batch with disintegration time 26.34 ± 0.78 s and in vitro release 99.64 ± 0.43% was selected as optimized formulation. This formulation was compared with conventional marketed formulation and was found superior. Batch F4 was subjected to stability studies for three months and was tested for its disintegration time, drug contents and dissolution behaviour. Batch F4 was found stable for three months at accelerated temperature.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.ijbiomac.2014.10.048 | DOI Listing |
Drug Dev Ind Pharm
January 2025
Department of Pharmaceutical Technology and Biopharmaceutics, Faculty of Pharmacy, Jagiellonian University Medical College, ul. Medyczna 9, 30-688 Krakow, Poland.
Introduction: Liquisolid (LS) technology is particularly advantageous for poorly water-soluble drugs administered in very low doses because of the improved dissolution rate and superior content uniformity. However, there is a lack of research papers describing the application of this concept on an industrial scale. Thus, we present trials conducted to develop tablets containing 0.
View Article and Find Full Text PDFPharmaceuticals (Basel)
January 2025
Department of Drug Form Technology, Wroclaw Medical University, Borowska 211 A, 50-556 Wroclaw, Poland.
Introduction: The official implementation of pharmaceutical-grade cannabis raw materials for medicinal use has permitted doctors to prescribe and pharmacists to prepare cannabis-based formulations. The objective of the pharmaceutical development and manufacturing process optimization work was to propose a suppository formulation containing doses of 25 mg and 50 mg of tetra-hydrocannabinol (∆-9-THC) as an alternative to existing inhalable or orally administered formulations. The formulation could be used for rectal or vaginal administration, thereby providing dosage control in the treatment of endometriosis and other conditions involving pain.
View Article and Find Full Text PDFMolecules
January 2025
Organization for Marine Science and Technology, Nagasaki University, 1-14 Bunkyo-machi, Nagasaki 852-8521, Japan.
High-Density Polyethylene (HDPE) and Low-Density Polyethylene (LDPE) films were used to create nanoplastic (NP) models, with the shape of delamination occurring during degradation. In the case of HDPE, selective degradation occurred not only in the amorphous part, but also in the crystalline part at the same time. Some of the lamellae that extend radially to form the spherulite structure were missing during the 30-day degradation.
View Article and Find Full Text PDFFoods
January 2025
College of Tourism and Culinary Institute, Yangzhou University, Yangzhou 225127, China.
This study examined the effects of varying microwave treatment durations (0-120 s) on the structural and functional properties of glycosylated soybean 7S protein. The results indicated that microwaving for 60 s significantly altered the structure of 7S, resulting in a more ordered protein configuration. The treated protein exhibited the largest particle size (152.
View Article and Find Full Text PDFEur J Pharm Sci
January 2025
RAPSODEE, IMT Mines Albi, CNRS, University of Toulouse, 81013 Albi, France.
This study investigates the effects of disintegrants sodium starch glycolate (SSG) and crospovidone (CP) on the printability, rheological properties, and disintegration time of agar and hydroxypropyl methylcellulose (HPMC)-based formulations designed for semi-solid extrusion. Printability was assessed by measuring the dimensional accuracy of manually extruded filaments. Rheological analysis was performed using oscillatory measurements.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!