Developmental genetic studies of evolved differences in morphology have led to the hypothesis that cis-regulatory changes often underlie morphological evolution. However, because most of these studies focus on evolved loss of traits, the genetic architecture and possible association with cis-regulatory changes of gain traits are less understood. Here we show that a derived benthic freshwater stickleback population has evolved an approximate twofold gain in ventral pharyngeal tooth number compared with their ancestral marine counterparts. Comparing laboratory-reared developmental time courses of a low-toothed marine population and this high-toothed benthic population reveals that increases in tooth number and tooth plate area and decreases in tooth spacing arise at late juvenile stages. Genome-wide linkage mapping identifies largely separate sets of quantitative trait loci affecting different aspects of dental patterning. One large-effect quantitative trait locus controlling tooth number fine-maps to a genomic region containing an excellent candidate gene, Bone morphogenetic protein 6 (Bmp6). Stickleback Bmp6 is expressed in developing teeth, and no coding changes are found between the high- and low-toothed populations. However, quantitative allele-specific expression assays of Bmp6 in developing teeth in F1 hybrids show that cis-regulatory changes have elevated the relative expression level of the freshwater benthic Bmp6 allele at late, but not early, stages of stickleback development. Collectively, our data support a model where a late-acting cis-regulatory up-regulation of Bmp6 expression underlies a significant increase in tooth number in derived benthic sticklebacks.

Download full-text PDF

Source
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC4183278PMC
http://dx.doi.org/10.1073/pnas.1407567111DOI Listing

Publication Analysis

Top Keywords

tooth number
16
cis-regulatory changes
12
derived benthic
8
quantitative trait
8
developing teeth
8
bmp6
6
tooth
6
cis-regulatory
5
evolved
4
evolved tooth
4

Similar Publications

BACKGROUND A tooth preparation's clinical requirements and geometric configurations should take precedence over material characteristics when advocating for putty reline impression techniques for permanent restorations, since they require a technically sensitive spacer for light body elastomer. We evaluated the linear dimensional accuracy of vinyl polysiloxane-based putty reline impressions with different spacer acquisition techniques in short-span and long-span fixed partial dentures (FPD). MATERIAL AND METHODS A typodont tooth set simulated a 3-unit (short-span) and a 5-unit (long-span) FPD.

View Article and Find Full Text PDF

Perioperative changes in anxiety and comfort in third molar extraction patients sedated with midazolam.

Oral Maxillofac Surg

January 2025

Department of Oral and Maxillofacial Surgery, Nara Medical University, 840, Shijo-Cho, 634-8522, Kashihara, Nara, Japan.

Purpose: This study aimed to analyze changes in anxiety and comfort levels at each perioperative stage during third molar extraction under single-agent intravenous midazolam sedation, and to clarify how these conditions at each perioperative stage affect postoperative satisfaction.

Patients And Method: 115 who requested extraction of 1 ~ 4 third molars under single-agent intravenous midazolam sedation were targeted. These patients were administered a questionnaire survey one week after surgery.

View Article and Find Full Text PDF

In vitro analysis of composition profiles of resins for 3D printing of dentures.

J Dent

January 2025

Clinic of General-, Special Care- and Geriatric Dentistry, Center for Dental Medicine, University of Zurich, Zurich, Switzerland. Electronic address:

Objective: This study aimed to investigate the resin compounds from CAD-CAM 3D-printed denture resins, focusing on the identification and classification of free monomers and other components. The primary objective was to determine the chemical profile of these 3D-prinding resin materials.

Methods: Four 3D-printed denture resins, two base materials (1: DentaBASE, Asiga Ltd.

View Article and Find Full Text PDF

Prevalence and type of removable prostheses manufactured in dental laboratories in Switzerland over the last 10 years.

Swiss Dent J

January 2025

Division of Gerodontology and Removable Prosthodontics, University Clinics of Dental Medicine, University of Geneva, Geneva, Switzerland.

Due to effective preventive measures and advanced techniques in operative dentistry, tooth loss occurs later in life and implant restorations have become a common solution for replacement of missing teeth. Therefore, the use of removable dental prostheses (RDPs) is expected to decline over time. This study aims to evaluate the expected decrease in the production of RDPs in Swiss dental laboratories over the past decade.

View Article and Find Full Text PDF

Objective: This study aimed to assess the proportions of complicated endodontic cases treated by undergraduate dental students in a University clinic now and in the past.

Material And Methods: Data were obtained from the electronic records and previous publications from the Faculty of Dentistry, University of Oslo, Norway. The operators were dental undergraduate students in their final 2 years of training.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!