Purpose: To provide comparative biomechanical evaluation of bicortical locking versus unicortical-abutting locking screw-plate fixation in a comminuted radius fracture model.
Methods: A validated synthetic substitute of the adult human radius with a 1.5-cm-long segmental mid-diaphyseal defect was used in the study to simulate a comminuted fracture. Stabilization was achieved with an 8-hole locking plate and either bicortical screws or unicortical-abutting screws. The specimens were tested using nondestructive cyclical loading in 4-point bending, axial compression, and torsion to determine stiffness and displacement and subsequently in 4-point bending to assess load to failure.
Results: There were no statistically significant differences between bicortical versus unicortical-abutting locking screw fixation in nondestructive 4-point bending, axial compression, and torsion. Both locking screw constructs also demonstrated comparable 4-point bending loads to failure.
Conclusion: The biomechanical equivalence between bicortical locking versus unicortical-abutting locking screw-plate fixation suggests that adequate locking plate fixation can be achieved without perforation of the far cortex. The abutment of the screw tip within the far cortex enhances the unicortical screw positional stability and thereby effectively opposes the displacement of the screw when subjected to bending or axial or rotational loads.
Clinical Relevance: Unicortical-abutting screws potentially offer several clinical advantages. They eliminate the need for drilling through the far cortex and thereby a risk of adjacent neurovascular injury or soft tissue structure compromise. They eliminate the issues associated with symptomatic screw prominence. They can decrease risk of refracture after screw-plate removal. In case of revision plating, they permit conversion to bicortical locking screws through the same near-cortex screw holes, which eliminates the need for a longer or repositioned plate.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.jhsa.2014.06.141 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Unicortical Versus Bicortical Proximal Locking Screw for Prevention of Peri-Implant Fracture: A Biomechanical Analysis of an Osteoporotic Distal Radius Model.
J Hand Surg Glob Online
November 2024
The Curtis National Hand Center, MedStar Union Memorial Hospital, Baltimore, MD.
Purpose: Osteoporotic patients are at risk of peri-implant fractures after distal radius fixation. A unicortical screw in the proximal hole of the plate can theoretically decrease stress riser formation by eliminating the hole in the far bone cortex. This construct has been proposed in orthopedic literature to prevent peri-implant fractures but has not been tested in an osteoporotic distal radius model.
View Article and Find Full Text PDFBicortical Compression and Construct Stability With Variable Pitch Locking Screws in Cadaveric Specimens.
J Orthop Trauma
October 2024
Department for Orthopaedics and Rehabilitation, Penn State College of Medicine, Hershey, PA.
Article Synopsis
- The study aimed to evaluate the effectiveness of variable pitch locking screws in providing better interfragmentary and plate-bone compression compared to standard locking screws in cadaver bone, focusing on biomechanical stability.
- Nine pairs of fresh-frozen cadaver specimens were tested for differences in compression forces and overall stability using both screw types under different loading conditions.
- Results showed that variable pitch screws provided significantly greater interfragmentary and plate-bone compression, while no significant differences were found in the stability of constructs during cyclic loading or in 4-point bending tests.
Effect of Screw Length in Volar Plating for Intra-Articular Distal Radius Fractures: A Biomechanical Study.
J Hand Surg Am
December 2024
Department of Orthopedic Surgery, Washington University School of Medicine, St. Louis, MO. Electronic address:
Purpose: The purpose of this study was to compare the effect of varying screw lengths on load to failure and retention of the dorsal ulnar corner fragment after fixation of comminuted intra-articular distal radius fractures in a cadaveric model.
Methods: Twenty-four fresh frozen cadaveric forearms were subjected to a standardized distal radius osteotomy to mimic an intra-articular fracture pattern. Dual X-ray absorptiometry scans were performed to ensure minimal variability in bone density.
Does the proximal screw type affect stress and strain in pastern arthrodesis with locking plate in horses?
Res Vet Sci
October 2024
Department of Surgery, School of Veterinary Medicine and Animal Science, University of São Paulo, São Paulo, Brazil.
The implantation of unicortical cortex screws in the proximal hole of locking compression plates (LCP) has been recommended for proximal interphalangeal (PIP) arthrodesis in horses to prevent fractures resulting from stress risers in the proximal phalanx (P1). However, this cortex screw fixation technique may limit efficient dorsal compression of the PIP joint by the plate, potentially affecting the stability of the construct. In this study, we aimed to measure stress and strain in P1 and the plate using an ex vivo model of PIP arthrodesis in horses.
View Article and Find Full Text PDFBackground: Displaced diaphyseal fractures can be reduced using the push-pull technique, wherein a plate is affixed to the distal fragment of the fracture, a post screw is placed proximal to the plate, and a lamina spreader creates distraction. This study evaluated the load to failure and mechanism of failure of bicortical and unicortical post screws during reduction.
Materials And Methods: Four matched pairs of cadaver legs were subjected to a 2-cm oblique osteotomy simulating a displaced, oblique diaphyseal fracture.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!