Objective: The purpose of this study was to evaluate the mechanical behavior of two different straight prosthetic abutments (one- and two-piece) for external hex butt-joint connection implants using three-dimensional finite element analysis (3D-FEA).
Materials And Methods: Two 3D-FEA models were designed, one for the two-piece prosthetic abutment (2 mm in height, two-piece mini-conical abutment, Neodent) and another one for the one-piece abutment (2 mm in height, Slim Fit one-piece mini-conical abutment, Neodent), with their corresponding screws and implants (Titamax Ti, 3.75 diameter by 13 mm in length, Neodent). The model simulated the single restoration of a lower premolar using data from a computerized tomography of a mandible. The preload (20 N) after torque application for installation of the abutment and an occlusal loading were simulated. The occlusal load was simulated using average physiological bite force and direction (114.6 N in the axial direction, 17.1 N in the lingual direction and 23.4 N toward the mesial at an angle of 75° to the occlusal plan).
Results: The regions with the highest von Mises stress results were at the bottom of the initial two threads of both prosthetic abutments that were tested. The one-piece prosthetic abutment presented a more homogeneous behavior of stress distribution when compared with the two-piece abutment.
Conclusions: Under the simulated chewing loads, the von Mises stresses for both tested prosthetic-abutments were within the tensile strength values of the materials analyzed which thus supports the clinical use of both prosthetic abutments.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC4053675 | PMC |
| http://dx.doi.org/10.4103/1305-7456.120642 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Evaluation of stress patterns in teeth with endodontic treatment and periapical lesions as abutments for fixed prosthesis: a finite element analysis study.
BMC Oral Health
January 2025
Department of Agr. Machinery and Technology Engineering, Akdeniz University, Antalya, Turkey.
Background: Examining stress distributions in abutment teeth with periapical lesions is essential for understanding their biomechanical impact on dental structures and tissues. This study uses finite element analysis (FEA) to evaluate these stress patterns under occlusal forces, aiming to enhance treatment strategies and prosthetic designs.
Methods: Three FEA models were created: a healthy mandibular premolar (Model 1), a premolar with a single crown and a lesion repaired using a fiber-post (Model 2), and 3) a premolar with a lesion repaired using fiber-post to support a four-member bridge (Model 3).
Evaluation of keratinized tissue augmentation using amnion/chorion allograft vs. autogenous connective tissue in implant therapy: a retrospective study.
Clin Oral Investig
January 2025
Department of Surgical Sciences and Integrated Diagnostics, Unit of Implant and Prosthetic Dentistry, University of Genoa, Largo R. Benzi 10 , 16121 , Genova, Italy.
Objectives: Successful implant therapy must also ensure the integration of the soft tissues around the crown/abutment emergence profile. The existing literature does not consistently agree on the necessity of a minimal amount of keratinized tissue (KT), though it appears advantageous for the long-term stability and aesthetics of implants. The purpose of this clinical retrospective study is to compare the effectiveness of amnion/chorion membrane and autogenous subepithelial connective tissue in increasing the keratinized mucosa and maintaining it over a 5-year follow-up.
View Article and Find Full Text PDFFrom model validation to biomechanical analysis: In silico study of multirooted root analogue implants using 3D finite element analysis.
J Mech Behav Biomed Mater
January 2025
Oral Technology, Dental School, University Hospital Bonn, Bonn, Germany. Electronic address:
Objectives: To create a validated 3D finite element model and employ it to examine the biomechanical behaviour of multirooted root analogue implants (RAIs).
Methods: A validated finite element model comprising either an RAI or a threaded implant (TI) and an idealised bone block was developed based on a previously conducted in vitro study. All the experimental boundary conditions and material properties were reproduced.
Clinical and radiographic outcomes of extra-short implants (≤ 6 mm) in the posterior atrophic jaws: a retrospective cohort study.
Int J Implant Dent
January 2025
Department of Neurosciences, School of Dentistry, University of Padua, Padua, Italy.
Objective: This study aimed at investigating implant survival rate and marginal bone loss (MBL) around extra-short implants. The impact of the loading protocol and of the use of an intermediate abutment was also evaluated, to explore possible differences in terms of the outcome measures.
Materials And Methods: Patients with single or multiple mandibular or maxillary posterior edentulism rehabilitated using extra-short 5-6 mm long implants were included.
The influence of prosthetic treatments and implant-supported prostheses on posterior mandibular ridge atrophy: a retrospective cohort study.
BMC Oral Health
January 2025
Division of Restorative Dentistry, Periodontology and Prosthodontics, Department of Dental Medicine and Oral Health, Medical University of Graz, Billrothgasse 4, Graz, 8010, Austria.
Aims: Bone preservation is a requirement for long-term stability of dental prostheses, which is all the more important in the posterior mandible, given the particular challenges these areas pose to prosthetic treatment. The objective was to investigate the implications of different prostheses on the atrophy of posterior alveolar bone after tooth loss.
Materials And Methods: A total of 457 treatment cases were retrieved from the medical documentation and information network.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!