Deformation of the anterior teeth and palatal regions on upper complete dentures was investigated using the photoelastic coating method and strain gages. In this experiment, an uniform-moment bending load method was employed to simulate the occlusal situation, and the distribution of strain in epoxy resin, stainless swaged and Co-Cr alloy cast dentures were measured and analyzed. The 030-series reflection polariscope is compact and lightweight with its main components consisting of two polarizer/quarter-wave-plate assemblies attached to a common frame. The highest level of strain was seen in the anterior region of the palate and the low strain was observed in other regions. Differences in strain magnitude of the three dentures were not observed with test at the same point. But, when denture base materials with high flexural rigidity and bending strength were used on the palatal region of the denture base, strain was decreased in the anterior and other regions of the palate. Therefore, dentures using those materials could be effectively reinforced.
Download full-text PDF |
Source |
|---|
Publication Analysis
Top Keywords
Similar Publications
CADCAM Versus Conventional Denture Bases: Network Meta-Analysis of In Vitro Studies Comparing Accuracy and Surface Properties.
Int Dent J
January 2025
Department of Pharmacy Practice, School of Pharmacy, College of Pharmacy, IMU University, Kuala Lumpur, Wilayah Persekutuan, Malaysia.
Introduction: This systematic review with network meta-analysis (NMA) analysed the current evidence on in vitro studies comparing trueness of fit, surface roughness, colour stability, surface wettability, water sorption, water solubility, and microbial adhesion between conventional and digital denture bases.
Methods: From inception until December 2023, a systematic search of published in-vitro studies from Scopus, PubMed, and the Cochrane Central Register of Controlled Studies was conducted. The protocol was registered in PROSPERO (CRD42024531416).
Antimicrobial activity and applications in PMMA of a novel benzpyrole derivant/iodocuprate hybrid (TMBI)(CuI).
Bioorg Chem
January 2025
Fujian Key Laboratory of Oral Diseases, Fujian Biological Materials Engineering and Technology Center of Stomatology, School and Hospital of Stomatology, Fujian Medical University, Fuzhou, Fujian 350004, China; Department of Prosthodontics, School and Hospital of Stomatology, Fujian Medical University, Fuzhou 350001, China. Electronic address:
Among individuals who wear removable dentures, there is a significant likelihood, reaching up to 70 %, of experiencing a condition known as denture-induced stomatitis. To address this issue, a commonly used method involves soaking dentures in denture cleansers to eliminate microorganisms. However, the prolonged use of this cleaning method has resulted in the emergence of drug resistance.
View Article and Find Full Text PDFMicrobial Adhesion and Cytotoxicity of Heat-Polymerized and 3D-Printed Denture Base Materials when Modified with Dimethylaminohexadecyl Methacrylate and/or 2-Methacryloyloxyethyl Phosphorylcholine as Antimicrobial and Protein-Repellent Materials.
Polymers (Basel)
January 2025
Department of Advanced Oral Sciences and Therapeutics, University of Maryland School of Dentistry, Baltimore, MD 21201, USA.
Background: Polymethyl methacrylate (PMMA) is ideal for denture bases but is prone to biofilm accumulation, leading to denture stomatitis (DS), often involving . Dimethylaminohexadecyl methacrylate (DMAHDM) and 2-methacryloyloxyethyl phosphorylcholine (MPC) are introduced into dental materials for their antimicrobial and protein-repellent properties. This study investigates the effects of incorporating dimethylaminohexadecyl methacrylate (DMAHDM) and 2-methacryloyloxyethyl phosphorylcholine (MPC) into heat-polymerized (HP) and 3D-printed (3DP) denture base resins on microbial adhesion and cytotoxicity.
View Article and Find Full Text PDFGingival margin interfacial microleakage, staining, and push-out strengths of gingival colored composite resins in denture bases.
J Prosthet Dent
January 2025
Professor, Department of Dentistry, Federal University of Santa Catarina (UFSC), Florianópolis, SC, Brazil. Electronic address:
Statement Of Problem: Staining at the gingival margin could impact denture longevity, but the behavior of gingival colored composite resins (GCCs) in this area remains unclear.
Purpose: This in vitro study evaluated surface staining, microleakage, and push-out bond strength at the gingival margin of artificial teeth, comparing two consistencies of GCCs with two resin base materials.
Material And Methods: Specimens included artificial teeth (Ivostar; Ivoclar AG) and two acrylic resin base materials: conventional (Ondacryl; Clássico) and high-impact (Diamond D; Keystone Industries) (n=300).
Physical-mechanical properties and accuracy of additively manufactured resin denture bases: Impact of printing orientation.
J Prosthodont Res
January 2025
Department of Prosthodontics, Faculty of Dentistry, Ibb University, Ibb, Yemen.
Purpose: This systematic review evaluated the effect of different printing orientations on the physical-mechanical properties and accuracy of resin denture bases and related specimens.
Study Selection: Utilizing PRISMA 2020 guidelines, a comprehensive search of PubMed, Web of Science, Cochrane, and Scopus databases was conducted until June 2024. Included studies examined the accuracy, volumetric changes, and mechanical or physical properties of 3D-printed denture bases in various orientations.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!