Micromachined microphones with grating-based optical-interferometric readout have been demonstrated previously. These microphones are similar in construction to bottom-inlet capacitive microelectromechanical-system (MEMS) microphones, with the exception that optoelectronic emitters and detectors are placed inside the microphone's front or back cavity. A potential advantage of optical microphones in designing for low noise level is the use of highly-perforated microphone backplates to enable low-damping and low thermal-mechanical noise levels. This work presents an experimental study of a microphone diaphragm and backplate designed for optical readout and low thermal-mechanical noise. The backplate is 1 mm × 1 mm and is fabricated in a 2-μm-thick epitaxial silicon layer of a silicon-on-insulator wafer and contains a diffraction grating with 4-μm pitch etched at the center. The presented system has a measured thermal-mechanical noise level equal to 22.6 dBA. Through measurement of the electrostatic frequency response and measured noise spectra, a device model for the microphone system is verified. The model is in-turn used to identify design paths towards MEMS microphones with sub 15-dBA noise floors.
Download full-text PDF |
Source |
|---|---|
| http://www.ncbi.nlm.nih.gov/pmc/articles/PMC4032405 | PMC |
| http://dx.doi.org/10.1121/1.4871181 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Effect of size on the thermal noise and acoustic response of viscous-driven microbeams.
J Acoust Soc Am
April 2024
Department of Mechanical Engineering, Binghamton University, Binghamton, New York 13902, USA.
A study is presented of the thermal-mechanical noise and response to sound of microphones that are designed to be driven by the viscous forces in air rather than by sound pressure. Virtually all existing microphone designs are intended to respond to sound pressure. The structures examined here consist of thin, micro-scale, cantilever beams.
View Article and Find Full Text PDFDesign and Simulation of a System-in-Package Chip for Combined Navigation.
Micromachines (Basel)
January 2024
School of Electronic and Computer Engineering, Shenzhen Graduate School of Peking University, Shenzhen 518055, China.
This paper proposes a system-in-package combination navigation chip. We used wire bonding, chip stacking, surface mount, and other processes to integrate satellite navigation chips, inertial navigation chips, microprocessor chips, and separation devices. Finally, we realized the hardware requirements for combined navigation in a 20 mm × 20 mm chip.
View Article and Find Full Text PDFSensitive and broadband infrared sensors are required for security and medical applications, as few can rapidly and sensitively detect infrared without uncooled devices. Here, we report a wideband optical-detection strategy based on the thermoelastic effect of a coating-enhanced quartz tuning fork (QTF) and study the feasibility of using an atomic force probe operating in contact mode to monitor the vibration. Graphene oxide (GO) and polydimethylsiloxane (PDMS) coating were applied on the QTF's surface to improve the light absorption and the thermal-mechanical conversion efficiency.
View Article and Find Full Text PDFCoherent optical fiber networks are extremely sensitive to thermal, mechanical, and acoustic noise, which requires elaborate schemes of phase stabilization with dedicated auxiliary lasers, multiplexers, and photodetectors. This is particularly demanding in quantum networks operating at the single-photon level. Here, we propose a simple method of phase stabilization based on single-photon counting and apply it to quantum fiber networks implementing single-photon interference on a lossless beamsplitter and coherent perfect absorption on a metamaterial absorber.
View Article and Find Full Text PDFMicro-grating accelerometer detecting small displacement by an optical system can be widely applied in inertial navigation and seismic monitoring. We proposed a micro-grating accelerometer prototype with a proof mass of gram-scale to decrease the thermal mechanical noise, which is the fundamental limit of a high-resolution accelerometer. The theoretical model for the contrast ratio of a micro-grating accelerometer is established based on Gaussian beam theory, and the adjustment method based on a scanning slit beam profiler improves the contrast ratio of 0th order effectively.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!