Introduction: Surgically assisted rapid palatal expansion (SARPE) is the procedure of choice for treatment of adults with transverse maxillary deficiency greater than 7 mm. There is no consensus about the dentoskeletal effect of an orthodontic retainer on the outcome of SARPE. Our objective was to assess the effectiveness of an orthodontic retainer on dentoskeletal stability.
Methods: Ninety digitized dental casts of 30 adults undergoing SARPE were divided into 2 groups-no retention (n = 15) and retention (n = 15)-and assessed. The dental casts were obtained at 3 checkpoints: (1) 7 days on average before SARPE (preoperatively), (2) 4 months after expansion, and (3) 10 months after expansion was completed. The retention patients received a transpalatal arch just after expander removal, at checkpoint 2. The transpalatal arch was kept for 10 months after completion of the expansion (checkpoint 3 and end of the study). The dental casts were scanned with a Vivid 9i 3D laser scanner (Konica Minolta, Wayne, NJ). The distances measured were premolar and molar intercusp distances, premolar and molar intercervical distances, premolar and molar inter-WALA (Will Andrews and Lawrence Andrews) ridge distances, and palate height at the maxillary first molar.
Results: The planned maxillary expansion was within the expected amount (P <0.05). Palatal height at the 4-month checkpoint decreased by 0.79 mm (4.38%) (P <0.001) and again at the 10-month checkpoint by 0.38 mm (0.98%) (P >0.05) but not significantly in both groups. The premolar intercusp distance had a relapse at checkpoint 3 of 1.84 mm (7.18%) (P <0.001) in the no-retention group. Both groups had average relapses of 0.95 mm in the premolar intercervical distances, of 0.88 mm in the premolar inter-WALA ridge distances, of 1.04 mm in the molar intercusp distances, of 0.74 mm in the molar intercervical distances, and of 0.84 mm in the molar inter-WALA ridge distances (P <0.05) at checkpoint 3.
Conclusions: The analysis of relapse in both groups suggests that the use of a transpalatal arch as a retaining device does not improve dento-osseous stability.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.ajodo.2013.12.026 | DOI Listing |
Cureus
December 2024
Workman School of Dental Medicine, High Point University, High Point, USA.
Background: While the majority of dentists and lab techs recommend dental-specific desktop printers, many of them use cheaper, more affordable 3D printers in their practice. The study aimed to compare the accuracy of two commercial non-dental stereolithography (SLA) 3D printers with a dental 3D printer for diagnostic dental casts. Methods: A prototype stereolithographic (Standard Triangle/Tessellation Language (STL)) model of a dentoform was used as a master model to be printed by three 3D printers (n=10 for each printer).
View Article and Find Full Text PDFMaterials (Basel)
January 2025
Department of Biomedical Engineering, Iwate Medical University, Iwate 028-3694, Japan.
This study aimed to investigate the release of metallic ions from cobalt-chromium (Co-Cr) alloys fabricated by additive manufacturing (AM) for comparison with dental casting. Co-Cr alloys were fabricated via AM using selective laser melting (SLM) and electron beam melting (EBM) in powder-bed fusion. Polished and mechanically ground specimens were prepared.
View Article and Find Full Text PDFMedicina (Kaunas)
January 2025
Faculty in Pediatric Dentistry and Orthodontics, College of Dentistry, King Saud University, Riyadh P.O. Box 11545, Saudi Arabia.
The palate's morphological characteristics are of great importance, especially in periodontology, where the palatine tissue represents a source of tissue graft for multiple mucogingival surgeries. This study aimed to estimate the amount of donor tissue available through the average palatal height and average location of the greater palatine artery in the Saudi population according to age and gender. Digital casts for adult Saudi patients at the age of 18-60 years old with a mean age of 37.
View Article and Find Full Text PDFMinerva Dent Oral Sci
January 2025
School of Dentistry, Department of Biomedical and Dental Sciences and Morphofunctional Imaging, University of Messina, Messina, Italy -
Alginates are widely used in dentistry for various applications due to their favorable properties, including ease of use, cost-effectiveness, and patient comfort. They are commonly employed for preliminary impressions of oral structures in dental practice. This study aims to assess the impact of different factors on the performance of alginate impression materials in dentistry.
View Article and Find Full Text PDFEur J Oral Sci
January 2025
Department of Biology, Faculty of Science, Ege University, Izmir, Turkiye.
The aims of this study were twofold: first, to investigate the surface roughness of different abutment materials prepared using various manufacturing methods; and, second, to evaluate colonization by Streptococcus mutans and Candida albicans according to abutment material and manufacturing method. Six material/manufacturing method combinations were investigated in this study, namely chromium-cobalt (Cr-Co) (prepared using casting, milling, and laser sintering) and titanium, zirconia, and anodized titanium (all prepared using milling); titanium (stock) abutments were used as the control group. Surface roughness of seven specimens from each group was evaluated using atomic force microscopy and scanning electron microscopy.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!