Transition between mechanisms of laser-induced field-free molecular orientation.

Phys Rev Lett

Max-Planck Institute of Quantum Optics, Hans-Kopfermann-Strasse 1, D-85748 Garching, Germany and J. R. Macdonald Laboratory, Physics Department, Kansas State University, 116 Cardwell Hall, Manhattan, Kansas 66506, USA.

Published: March 2014

The transition between two distinct mechanisms for the laser-induced field-free orientation of CO molecules is observed via measurements of orientation revival times and subsequent comparison to theoretical calculations. In the first mechanism, which we find responsible for the orientation of CO up to peak intensities of 8 × 10(13) W/cm(2), the molecules are impulsively oriented through the hyperpolarizability interaction. At higher intensities, asymmetric depletion through orientation-selective ionization is the dominant orienting mechanism. In addition to the clear identification of the two regimes of orientation, we propose that careful measurements of the onset of the orientation depletion mechanism as a function of the laser intensity will provide a relatively simple route to calibrating absolute rates of nonperturbative strong-field molecular ionization.

Download full-text PDF

Source
http://dx.doi.org/10.1103/PhysRevLett.112.113005DOI Listing

Publication Analysis

Top Keywords

mechanisms laser-induced
8
laser-induced field-free
8
orientation
6
transition mechanisms
4
field-free molecular
4
molecular orientation
4
orientation transition
4
transition distinct
4
distinct mechanisms
4
field-free orientation
4

Similar Publications

Micromodification in bulk undoped polymethylmethacrylate (PMMA) by single focused (numerical aperture (NA) = 0.25), 1030-nm 250-fs laser pump pulses was explored by pump self-transmittance; optical, 3D-scanning confocal photoluminescence (PL); Raman micro-spectroscopy; and optical polarimetric and interferometric microscopy. Starting from the threshold pulse energy  = 0.

View Article and Find Full Text PDF

Laser processing materials for photo-to-thermal applications.

Adv Colloid Interface Sci

December 2024

School of Materials Science and Engineering, Shaanxi Key Laboratory of Green Preparation and Functionalization for Inorganic Materials, Shaanxi University of Science and Technology, Xi'an, Shaanxi 710021, China.

Photothermal conversion materials (PCMs) are crucial component in solar-thermal energy technologies. Although various PCMs with excellent sunlight harvesting have been developed for colorful solar-thermal applications, uniform and large-scale production of PCMs remains a challenge, and the PCMs prepared through the conventional methods are often non-site specific. Laser processing technology (LPT), as an efficient, convenient, green and sustainable technology, can directly create micro/nano structures and patterns at specific locations on materials surface, attracting widespread attention in photo-to-thermal applications.

View Article and Find Full Text PDF

Inspired by lotus leaf, biomimetic hydrophobic cellulose fiber-based textiles were usually fabricated by the lower surface energy materials. However, it is rare to witness a hydrophobic surface obtained by near infrared laser (NIR) irradiation a superhydrophilic nanomaterial, which remains a huge challenge. Herein, the CuS nanospheres was in-situ anchored on the surface of gallic acid self-polymer treated cotton fabric.

View Article and Find Full Text PDF

The poor interlaminar fracture toughness is a critical limiting factor for the structural applications of aramid fiber/epoxy resin composites. This study investigates the effects of laser-induced graphene (LIG) and short Kevlar fibers on the interfacial toughness and damage detection of aramid composite materials. Mode II tests and tensile tests were conducted to evaluate mechanical properties and damage detection using the piezoresistive characteristics of LIG.

View Article and Find Full Text PDF

Over the past decade, Tunnel Oxide Passivated Contact (TOPCon) solar cells have emerged as a leading technology for high-efficiency silicon solar cells. Conventional metallization processes using silver/aluminum (Ag/Al) pastes encounter significant hurdles due to reliability risks and insufficient contact quality. Recent advancements in laser-induced metallization technologies, particularly laser-enhanced contact optimization (LECO), offer promising solutions.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!