Purpose: This study evaluated the sorption and solubility of self-etching adhesive systems after immersion in distilled water, lactic acid, and propionic acid.
Materials And Methods: Specimens of 2 two-step (P90 System Adhesive [P90], Clearfil SE Bond [CSE]) and 1 single-step (Adper Easy One [AEO]) adhesive systems were prepared and divided into 4 groups: P90 primer ( P90-P), P90 bond (P90-B), AEO, and CSE bond (CSE-B). Specimens were placed in a desiccator and weighed daily until achieving a constant mass (m1). The specimens (n = 5) were then immersed in the respective media and weighed until a achieving a constant mass (m2). The specimens were again desiccated (m3). Sorption and solubility data were analyzed with two-way ANOVA and Turkey's test. Specimens were also observed using SEM without immersion, after 24 h, and at the end of the respective total time of immersion.
Results: For all immersion media, the highest sorption values were obtained for AEO and P90-P, followed by CSE-B and P90-B, which presented the lowest sorption. The time required for adhesives to absorb the solutions was: 11 to 19 days for P90-P, 12 to 13 days for P90-B, 15 to 19 days for AEO, and 14 to 18 days for CSE-B. The highest values of solubility were shown for AEO and P90-P in all immersion media. In water and propionic acid, the adhesives with the lowest solubility values were CSE-B and P90-B. CSE-B had the lowest solubility in lactic acid.
Conclusion: The greatest surface degradation was observed after each respective total time of immersion. AEO specimens presented more evident surface degradation and the highest sorption and solubility.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.3290/j.jad.a31813 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
CADCAM Versus Conventional Denture Bases: Network Meta-Analysis of In Vitro Studies Comparing Accuracy and Surface Properties.
Int Dent J
January 2025
Department of Pharmacy Practice, School of Pharmacy, College of Pharmacy, IMU University, Kuala Lumpur, Wilayah Persekutuan, Malaysia.
Introduction: This systematic review with network meta-analysis (NMA) analysed the current evidence on in vitro studies comparing trueness of fit, surface roughness, colour stability, surface wettability, water sorption, water solubility, and microbial adhesion between conventional and digital denture bases.
Methods: From inception until December 2023, a systematic search of published in-vitro studies from Scopus, PubMed, and the Cochrane Central Register of Controlled Studies was conducted. The protocol was registered in PROSPERO (CRD42024531416).
Fabrication of a poly(m‑aminophenol)/3-aminopropyl triethoxysilane/graphene oxide ternary nanocomposite for removal of Cu(II) from aqueous solution.
Sci Rep
January 2025
Chemistry Department, Faculty of Science, Tanta University, Tanta, 31527, Egypt.
Three composites based on Poly (meta-aminophenol) (PmAP), (3-aminopropyl) triethoxysilane (APTES) and graphene oxide (GO) were synthesized with initial GO dispersion of 3.3, 6.6, and 9.
View Article and Find Full Text PDFQuantum chemically calculated abraham parameters for quantifying and predicting polymer hydrophobicity.
Environ Toxicol Chem
January 2025
Environmental Science Division, Argonne National Laboratory, Lemont, IL, 60439, USA.
The leakage and accumulation of plastic in the environment is a significant and growing problem with numerous detrimental impacts and has led to a push toward the design and development of more environmentally benign materials. To this end we have developed a quantum chemistry (QC) based model for predicting the mobility of polymer materials from molecular structure. Hydrophobicity is used as a surrogate for mobility given that hydrophobic interactions drive much of the partitioning of contaminants in and out of various environmentally relevant compartments.
View Article and Find Full Text PDFComparative analysis of conversion and crosslinking degree in bulk-fill, monochromatic, and ORMOCER composites.
J Dent
January 2025
University of Saskatchewan, College of Dentistry. 107 Wiggins Rd, Saskatoon, SK, S7N 5E5, Canada. Electronic address:
Bulk-fill, monochromatic, and ORMOCER composites were introduced in restorative dentistry with the aim of reducing clinical time and/or alleviating contraction stresses at the interface between the tooth and restoration. While the conversion and immediate properties of these materials are comparable to conventional composites, studies evaluating their long-term properties and the structure of the polymer matrix are lacking. The objective of this study was to evaluate the degree of conversion and, indirectly, the crosslink density of conventional, bulk-fill, monochromatic, and ORMOCER resin composites.
View Article and Find Full Text PDFBiogas upgrading using aqueous bamboo-derived activated carbons.
Bioresour Technol
January 2025
Energy Engineering, Division of Energy Science, Luleå University of Technology, Luleå 97187, Sweden. Electronic address:
CO/CH separation is crucial for biogas upgrading. In this study, the bamboo-derived activated carbons (BACs) were prepared with different ratios of potassium hydroxide (KOH)/bamboo charcoal (BC), and the hybrid sorbents of aqueous BACs were developed for CO/CH separation. Both the gas solubility and sorption rate were measured, and Henry's constant and liquid-side mass-transfer coefficient as well as the CO/CH selectivity were calculated.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!