Solution-processed Ga-doped ZnO nanorod arrays as electron acceptors in organic solar cells.

ACS Appl Mater Interfaces

School of Applied Physics, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 UKM Bangi, Selangor, Malaysia.

Published: April 2014

This paper reports the utilization of ZnO nanorod arrays (NRAs) doped with various concentrations of Ga (0, 0.5, 1, 2, and 3 at %) as electron acceptors in organic solar cells. The donor, poly(3-hexylthiophene) (P3HT), was spin coated onto Ga-doped ZnO NRAs that were grown on fluorine-doped tin oxide (FTO) substrates, followed by the deposition of a Ag electrode by a magnetron sputtering method. Adjusting the Ga precursor concentration allowed for the control of the structural and optical properties of ZnO NRAs. The short circuit current density increased with increasing Ga concentration from 0 to 1 at %, mainly because of improved exciton dissociation and increased charge extraction. Meanwhile, the reduced charge recombination and lower hole leakage current led to an increase in the open circuit voltage with Ga concentrations up to 1 at %. The device with the optimum Ga concentration of 1 at % exhibited power conversion efficiency nearly three times higher compared to the device without Ga doping. This finding suggests that the incorporation of Ga can be a simple and effective approach to improve the photovoltaic performance of organic solar cells.

Download full-text PDF

Source
http://dx.doi.org/10.1021/am5007832DOI Listing

Publication Analysis

Top Keywords

organic solar
12
solar cells
12
ga-doped zno
8
zno nanorod
8
nanorod arrays
8
electron acceptors
8
acceptors organic
8
zno nras
8
solution-processed ga-doped
4
zno
4

Similar Publications

Suppressed Degradation Process of PBDB-TF-T1:BTP-4F-12-Based Organic Solar Cells with Solid Additive Atums Green.

ACS Appl Mater Interfaces

January 2025

Department of Physics, Chair for Functional Materials, TUM School of Natural Sciences, Technical University of Munich, James-Franck-Str. 1, 85748 Garching, Germany.

Solid additives have garnered significant attention due to their numerous advantages over liquid additives. This study explores the potential of the green-fluorescent conjugated polymer denoted Atums Green as a solid additive in green-solvent-based PBDB-TF-T1:BTP-4F-12 solar cells. Even tiny amounts of Atums Green doping significantly improve the device performance.

View Article and Find Full Text PDF

Construction of Nanocellulose Aerogels with Environmental Drying Strategy without Organic Solvent Displacement for High-Efficiency Solar Steam Generation.

ACS Nano

January 2025

Engineering Research Center of Forestry Biomass Materials and Bioenergy (Ministry of Education), National Forest and Grass Administration Woody Spices (East China) Engineering Technology Research Center, Beijing Forestry University, Beijing 100083, China.

Solar desalination is one of the effective means to alleviate water scarcity, in which aerogel-like evaporators have attracted extensive attention in the field of efficient desalination. However, the current preparation methods for aerogels still mainly rely on high-cost solutions, such as freeze-drying or supercritical drying. Herein, a preparation scheme for aerogels that can be realized under atmospheric pressure conditions is reported.

View Article and Find Full Text PDF

The rational design of non-fullerene acceptors (NFAs) with both high crystallinity and photoluminescence quantum yield (PLQY) is of crucial importance for achieving high-efficiency and low-energy-loss organic solar cells (OSCs). However, increasing the crystallinity of an NFA tends to decrease its PLQY, which results in a high non-radiative energy loss in OSCs. Here we demonstrate that the crystallinity and PLQY of NFAs can be fine-tuned by asymmetrically adapting the branching position of alkyl chains on the thiophene unit of the L8-BO acceptor.

View Article and Find Full Text PDF

Asphalt pavement emission behavior under solar radiation during in-service period.

J Hazard Mater

January 2025

School of Mechanical and Manufacturing Engineering, University of New South Wales, Sydney, NSW 2052, Australia.

The toxic fume emitted from asphalt pavement remains a health and environmental hazard towards public safety, especially the emission of volatile organic compounds (VOCs) and polycyclic aromatic hydrocarbons (PAHs). Despite extensive studies focused on characterizing asphalt fumes generated during construction stages (i.e.

View Article and Find Full Text PDF

Solar-driven desalination technology is currently an important way to obtain freshwater resources. Significantly, porous materials are used as substrate materials of interface solar evaporator, and their specific impact of water transport property and thermal management during evaporation is worth exploring. In this paper, poly(vinyl alcohol) (PVA) sponges were prepared by a chemical foaming method, adjusted the PVA polymerization degree, and formaldehyde-hydroxyl ratio to regulate the pore size, and polypyrrole (PPy) was grown in situ on the surface skeleton of PVA sponge to construct a new interfacial solar evaporator (PPy/PVA) with different pore structures.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!