The door-in-the-face technique increases the likelihood of individuals accepting a target request by confronting them, beforehand, with an extreme request. The present research tests a new door-in-the-face technique in which the two requests are formulated by two different requesters during the same interaction. 160 participants were asked to help a charity organization following a door-in-the-face procedure. According to the experimental conditions, requests were formulated by one or two requesters during the same or a different interaction. As predicted, the door-in-the-face effect was observed even if two requests are formulated by two requesters, but only if both are present during the interaction. Results are discussed in terms of a reciprocal concessions interpretation and a motivational interpretation.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.2466/17.07.PR0.113x25z7 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Application of response surface methodology in the formulation of spreadable creams from beechnut seeds as sustainable ingredient.
Food Sci Technol Int
January 2025
Food Engineering Department, Faculty of Food Science and Technology, University of Agricultural Sciences and Veterinary Medicine Cluj Napoca, Cluj Napoca, Romania.
Plants available in the spontaneous flora are recently studied as ingredients for food formulation in response to the demands for sustainable plant-based foods. The aim of this study was to obtain a new assortment of spreadable creams, free of palm oil, with good textural, rheological and colour attributes, high antioxidant activity and low cytotoxicity, from . (European beech) seeds.
View Article and Find Full Text PDFWhat Does Pharmaceutical 3D Printing Cost? A Framework and Case Study with Hydrocortisone for Adrenal Insufficiency.
Pharmacoecon Open
December 2024
Erasmus School of Health Policy & Management (ESHPM) & Erasmus Centre for Health Economics Rotterdam (EsCHER), Erasmus University Rotterdam, Burgemeester Oudlaan 50, 3062 PA, Rotterdam, The Netherlands.
Background: Pharmaceutical three-dimensional printing (3DP) technology offers an automated platform that can be utilized to manufacture personalized medicine, improving pharmacotherapy. Although 3D-printed products have entered clinical trials, no costing studies have been performed yet. Cost insights can aid researchers and industry in making informed decisions about the feasibility and scalability of 3DP.
View Article and Find Full Text PDFExploiting full-duplex opportunities in WLANs via a reinforcement learning-based medium access control protocol.
Sci Rep
December 2024
National University of Defense Technology, Changsha, Hunan, China.
In-band full-duplex communication has the potential to double the wireless channel capacity. However, how to efficiently transform the full-duplex gain at the physical layer into network throughput improvement is still a challenge, especially in dynamic communication environments. This paper presents a reinforcement learning-based full-duplex (RLFD) medium access control (MAC) protocol for wireless local-area networks (WLANs) with full-duplex access points.
View Article and Find Full Text PDFChanges in Medication Complexity and Post-Hospitalization Outcomes in Older Adults Hospitalized for Heart Failure.
Drugs Aging
December 2024
Department of Medicine, Weill Cornell Medicine, New York, NY, USA.
Introduction: Medication regimen complexity may be an important risk factor for adverse outcomes in older adults with heart failure. However, increasing complexity is often necessary when prescribing guideline-directed medical therapy at the time of a heart failure hospitalization. We sought to determine whether increased medication regimen complexity following a heart failure hospitalization was associated with worse post-hospitalization outcomes.
View Article and Find Full Text PDFDoes Cement Viscosity Impact Antibiotic Elution and In Vitro Efficacy Against Common Prosthetic Joint Infection Pathogens?
Clin Orthop Relat Res
October 2024
Rush Copley Medical Center, Aurora, IL, USA.
Background: Polymethylmethacrylate (PMMA) antibiotic-laden bone cement (ALBC) is commonly used in total joint arthroplasty to treat and potentially prevent prosthetic joint infection (PJI). Multiple properties impact the elution characteristics of antibiotics from PMMA-based ALBC, including viscosity. What is not known is how medium-viscosity cement formulations affect antibiotic elution and how different cement products from different manufacturers compare regarding reaching the minimum inhibitory concentration (MIC) of antibiotics for common PJI-causing organisms in an in vitro setting.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!