Statement Of Problem: Some silane primers and some zirconia primers contain extra resins such as bisphenol A glycol dimethacrylate (BisGMA) in their formulations for better wetting. No studies exist on the bonding properties of zirconia and silane primers, which contain extra resins.
Purpose: The purpose of this study was to investigate the effect of incorporating BisGMA resin on the bonding properties of silane and zirconia primers.
Material And Methods: Silica-base lithium disilicate was etched and treated with BisGMA-incorporated Porcelain Primer, unmodified Porcelain Primer, or resin-containing Kerr Silane. Zirconia ceramic was airborne-particle abraded and treated with BisGMA-incorporated Monobond Plus, unmodified Monobond Plus, or BisGMA-containing ZPrime Plus. After primer treatment and cleaning with ethanol, the contact angles were measured to determine surface change (n=10). Shear bond strength tests were also performed to measure the adhesion strength between resin cements and ceramic surfaces (n=10). Data were statistically analyzed by 1-way ANOVA followed by the Tukey multiple comparison as a post hoc test (significance level .05).
Results: The incorporation of BisGMA resin did not significantly influence the bond strength or contact angle of the zirconia primer (P>.05), but it did significantly reduce those of the silane primer (P<.05). Resin-containing Kerr Silane (22 degrees, 23 MPa) had a similar contact angle and higher bond strength than the control (21 degrees, 18 MPa), but lower than Porcelain Primer (88 degrees, 34 MPa). Resin-containing ZPrime Plus (75 degrees, 29 MPa) had a similar contact angle and higher bond strength than both Monobond Plus (74 degrees, 18 MPa) and the control (15 degrees, 4 MPa).
Conclusions: The addition of BisGMA resin significantly inhibited the efficacy of silane-containing porcelain primers but did not affect that of phosphate-containing zirconia primers.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.prosdent.2013.04.005 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Synergistic enhancement of hydrophobic dental adhesives: autonomous strengthening, polymerization kinetics, and hydrolytic resistance.
Front Dent Med
April 2024
Institute for Bioengineering Research, University of Kansas, Lawrence, KS, United States.
The leading cause of composite restoration failure is recurrent marginal decay. The margin between the composite and tooth is initially sealed by a low-viscosity adhesive, but chemical, physical, and mechanical stresses work synergistically and simultaneously to degrade the adhesive, destroying the interfacial seal and providing an ideal environment for bacteria to proliferate. Our group has been developing self-strengthening adhesives with improved chemical and mechanical characteristics.
View Article and Find Full Text PDFThe effect of photoinitiator systems on resin-based composite containing ZnO-nanoparticles.
Dent Mater
February 2025
Division of Dentistry, School of Medical Sciences, University of Manchester, Manchester, UK; Photon Science Institute, University of Manchester, Manchester, UK. Electronic address:
Objective: Zinc oxide (ZnO) powder possesses antibacterial activity and although white in color, it can severely reduce the depth of cure (DoC) of resin-based composite (RBC). This study investigated the effect of unary and binary photoinitiator systems on the DoC and degree of conversion (DC) of formulated RBC containing ZnO-nanoparticles.
Methods: Fourteen RBCs (n = 3/group) were formulated consisting of 50 wt% mixture of monomers (Bis-GMA, TEGDMA, and UDMA) and 50 wt% fillers (inert barium glass powder and silica nanoparticles).
Preparation of dental resin composites with anti-bacterial adhesion against Streptococcus mutans using fluorinated and silicon containing dimethacrylates.
Dent Mater
February 2025
College of Materials Science and Engineering, South China University of Technology, Guangzhou, China. Electronic address:
Objective: The purpose of this study was to enhance the anti-bacterial adhesion effect against Streptococcus mutans (S. mutans) of fluorinated dimethacrylate (DF MA) based dental resin composites (DRCs) by using silicone dimethacrylate (SMA-MEO).
Method: The SMA-MEO was added into mixture of DFMA and tricyclo (5.
Physical and mechanical characterizations of experimental pit and fissure sealants based on bioactive glasses.
J Clin Pediatr Dent
November 2024
Community Health Sciences Department, College of Applied Medical Sciences, King Saud University, 11451 Riyadh, Saudi Arabia.
Fissure sealants commonly exhibit weak mechanical and physical properties, potentially compromising their effectiveness in preventing dental caries. Therefore, this laboratory study aimed to synthesize and characterize experimental pit and fissure sealants in comparison with a commercially available sealant. Three different formulations of experimental pit and fissure sealing materials were synthesized using a blend of bisphenol A-glycidyl methacrylate (Bis-GMA) and triethylene glycol dimethacrylate (TEGDMA) monomers.
View Article and Find Full Text PDFThe Effect of Inorganic Filler Content on the Properties of BPA-Free Bulk-Fill Dental Resin Composites.
Materials (Basel)
October 2024
School of Materials Science and Engineering, South China University of Technology, Guangzhou 510641, China.
This study aimed to enhance the performance of dental resin composites (DRCs) by increasing the content of inorganic fillers while addressing potential health risks associated with Bisphenol A (BPA). To achieve this, the BPA-based resin monomer Bis-GMA was replaced with BPA-free Bis-EFMA. The study then explored the impact of varying inorganic filler contents on the physiochemical properties of Bis-EFMA-based bulk-fill dental resin composites (BF-DRCs).
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!