Polycabosilane (PCS) could be spun to form fiber web by electrospinning PCS solution in 30% dimethylformide (DMF)/toluene solvent at 25 kV. The electrospun web is stabilized at 200 degrees C for 1 hour to connect fibers by softening PCS webs and pyrolysed to synthesize silicon carbide (SiC) webs at 1800 degrees C. The pyrolysis at 1800 degrees C increased the SiC crystal size to 45 nm from 3 nm at 1300 degrees C. However, the pyrolysis at 1800 degrees C forms pores on the surface of SiC fibers due to oxygen evaporation generated during thermals curing. SiC/phenol composite webs could be fabricated by infiltration of phenol resin and hot pressing. The thermal conductivity measurement indicates that higher SiC fibers filler contents increase the thermal conductivity up to 1.9 W/mK for 40% fraction of filler contents from 0.5 W/mK for 20% fraction of filler.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1166/jnn.2013.7264 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Cellulose/sodium alginate gel electrolyte membranes with synergistic hydrogen bonding and metal ion coordination networks for high performance aqueous zinc-ion batteries.
Carbohydr Polym
March 2025
Institute of Zhejiang University-Quzhou, 99 Zheda Road, Quzhou 324000, China; National Key Laboratory of Biobased Transportation Fuel Technology, College of Biosystems Engineering and Food Science, Zhejiang University, Hangzhou 310058, China. Electronic address:
Cellulose has outstanding potential for application in energy storage batteries due to its high temperature resistance, high electrolyte affinity, renewability, and suppression of the shuttle effect, but single cellulose membranes still suffer from problems such as inhomogeneous pore distribution and unstable three-dimensional network structure. In this study, a green and sustainable regenerative cellulose (RC)/sodium alginate (SA) gel electrolyte membrane is developed by sol-gel process, the double crosslinked network scaffold centered on Zn was constructed by the synergistic hydrogen-bonding and metal ion- coordination network, the stable and uniform pore structure was also formed. The obtained RC-SA gel electrolyte membrane exhibits outstanding performance, featuring a dual crosslinked network with abundant pore structure and numerous polar groups that effectively enhance Zn transport, significantly improving battery cycling performance.
View Article and Find Full Text PDFEffects of Temperature and Water Vapor Content on Microstructure, Mechanical Properties and Corrosion Behavior of C/C-SiC Composites.
Materials (Basel)
December 2024
Aerospace Research Institute of Materials and Processing Technology, Beijing 100076, China.
Carbon-fiber-reinforced carbon and silicon carbide (C/C-SiC) composites were prepared using chemical vapor infiltration (CVI) combined with reactive melt infiltration (RMI). The microstructure and flexural properties of C/C-SiC composites after oxidation in different temperature water vapor environments were studied. The results indicate that the difficulty of oxidation in water vapor can be ranked from easy to difficult in the following order: carbon fiber (CF), pyrolytic carbon (PyC), and ceramic phase.
View Article and Find Full Text PDFEffects of Preformed Composition and Pore Size on Microstructure and Properties of SiC/SiC Composites via Reactive Melt Infiltration.
Materials (Basel)
November 2024
Zhejiang Key Laboratory of Data-Driven High-Safety Energy Materials and Applications, Ningbo Key Laboratory of Special Energy Materials and Chemistry, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201, China.
This study investigated the influence of preformed composition and pore size on the microstructure and properties of SiC/SiC composites fabricated via reactive melt infiltration (RMI). The process began with the impregnation of SiC fiber cloth with phenolic resin, followed by lamination and pyrolysis. Subsequent steps included further impregnations with phenolic resin, SiC slurry, and carbon black slurry, each followed by additional pyrolysis.
View Article and Find Full Text PDFFabrication, Microstructural Evolution, and Mechanical Properties of SiC/(HfTaZrNb)C/C Nanocomposites.
Materials (Basel)
October 2024
Key Laboratory of High Performance Ceramic Fibers, Xiamen University, Xiamen 361005, China.
A dense monolithic SiC/(HfTaZrNb)C/C high-entropy ceramic nanocomposite was prepared using a polymer-derived ceramic (PDC) method combined with spark plasma sintering (SPS). The microstructural evolution and mechanical properties of the obtained nanocomposites were characterized by X-ray diffractometer (XRD), transmission electron microscope (TEM), scanning-electron microscope (SEM), and nanoindentation. The results indicate that the phase composition of SiC/(HfTaZrNb)C/C can be adjusted by modifying the metal content of the single-source precursor (SSP) through molecular design.
View Article and Find Full Text PDFMicrostructure Evolution of the Interface in SiC/TiC-TiSiC Composite under Sequential Xe-He-H Ion Irradiation and Annealing Process.
Nanomaterials (Basel)
October 2024
State Key Laboratory of Nonlinear Mechanics, Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190, China.
A new type of SiC/TiC-TiSiC composite was prepared by the Spark Plasma Sintering (SPS) method in this work. The phase transformation and interface cracking of this composite under ion irradiation (single Xe, Xe + He, and Xe + He + H ions) and subsequent annealing were analyzed using transmission electron microscopy (TEM), mainly focusing on the interface regions. Xe ion irradiation resulted in the formation of high-density stacking faults in the TiC coatings and the complete amorphization of SiC fibers.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!