Colloidal lead chalcogenide (IV-VI) quantum dots and rods are of widespread scientific and technological interest, owing to their size tunable energy band gap at the near-infrared optical regime. This article reviews the development and investigation of IV-VI derivatives, consisting of a core (dot or rod) coated with an epitaxial shell, when either the core or the shell (or both) has an alloy composition, so the entire structure has the chemical formula PbSexS1-x/PbSeyS1-y (0 ≤ x(y) ≤ 1). The article describes synthesis procedures and an examination of the structures' chemical and temperature stability. The investigation of the optical properties revealed information about the quantum yield, radiative lifetime, emission's Stokes shift and electron-phonon interaction, on the variation of composition, core-to-shell division, temperature and environment. The study reflected the unique properties of core-shell heterostructures, offering fine electronic tuning (at a fixed size) by changing their architecture. The optical observations are supported by the electronic band structure theoretical model. The challenges related to potential applications of the colloidal lead chalcogenide quantum dots and rods are also briefly addressed in the article.

Download full-text PDF

Source
http://dx.doi.org/10.1039/c3nr02141fDOI Listing

Publication Analysis

Top Keywords

alloy composition
8
colloidal lead
8
lead chalcogenide
8
quantum dots
8
dots rods
8
tuning electronic
4
electronic properties
4
properties iv-vi
4
iv-vi colloidal
4
colloidal nanostructures
4

Similar Publications

An elastocaloric thermal battery based on generative learning-designed phase-change alloys is developed to facilitate the efficient recycling of low-temperature waste heat. This battery stores thermal energy as latent heat in a phase-change alloy and releases it on demand through applied stress at ambient temperature. Alloy compositions and corresponding processing parameters, tailored to desired transformation characteristics, are efficiently discovered through a generative learning-enabled inverse design framework, which converts the hand-drawn target heat flow curve into tangible compositional and processing designs.

View Article and Find Full Text PDF

Discovery and Characterization of a Metastable Cubic Interstitial Nickel-Carbon System with an Expanded Lattice.

ACS Nano

January 2025

Faculty III Process Sciences, Institute of Materials Science and Technology, Chair of Advanced Ceramic Materials, Technische Universität Berlin, Straße des 17. Juni 135, 10623 Berlin, Germany.

Metastable, , kinetically favored but thermodynamically not stable, interstitial solid solutions of carbon in iron are well-understood. Carbon can occupy the interstitial atoms of the host metal, altering its properties. Alloying of the host metal results in the stabilization of the FeC phases, widening its application.

View Article and Find Full Text PDF

Supercycle Al-Doped ZnMgO Alloys via Atomic Layer Deposition for Quantum Dot Light-Emitting Diodes.

ACS Appl Mater Interfaces

January 2025

Department of Photonics and Nanoelectronics, and BK21 FOUR ERICA-ACE Center, Hanyang University, Ansan 15588, Korea.

Colloidal quantum-dot light-emitting diodes (QD-LEDs) have been significantly improved in terms of device performance and lifetime by employing zinc oxide (ZnO) as an electron transport layer (ETL). Although atomic layer deposition (ALD) allows fabrication of uniform, high-quality ZnO films with minimal defects, the high conductivity of ZnO has hindered its straightforward application as an ETL in QD-LEDs. Herein, we propose fabrication of Al-doped ZnMgO (Al:ZnMgO) ETLs for QD-LEDs through a supercycle ALD, with alternating depositions of various metal oxides.

View Article and Find Full Text PDF

This paper presents the preparation of the parental experimental alloy, featuring a standard composition of TiYZrFeNiMn, via the vacuum induction melting technique. Subsequently, the TiYZrFeNiMn alloy, with an addition of 2 wt% Ni, underwent mechanical ball milling to yield a TiFe-based composite for experimental purposes. The results of the experimental tests indicate that the composite alloy's phase composition comprises the TiFe primary phase, with a minor quantity of ZrMn phase segregated on the surface of the primary TiFe phase, as well as Ni phase.

View Article and Find Full Text PDF

The current work outlines the preparation of a TiO nanotube (NT) layer electrochemically formed on the surface of a clinically-relevant titanium alloy anodisation. This NT layer was subsequently modified alternating current electrodeposition to incorporate copper micro- and nanoparticles on top of and within the NTs. Physical characterisation of the NT layer and the copper-incorporated NTs was carried out through analysis of the surface morphology, elemental composition, crystallinity, and stability SEM, EDX, XRD, and ICP-OES, respectively.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!