Frequency-resolved scanning photoresponse microscopy of pentacene thin-film transistors is reported. The photoresponse pattern maps the in-plane distribution of trap states which is superimposed by the level of trap filling adjusted by the gate voltage of the transistor. Local hotspots in the photoresponse map thus indicate areas of high trap densities within the pentacene thin film.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1002/adma.201300958 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Reduction in Population After a Year-Long Application of Targeted Sterile Insect Releases in the West Valley Region of Southern California.
Insects
January 2025
West Valley Mosquito and Vector Control District, 1295 East Locust St, Ontario, CA 91761, USA.
is of great public health concern because of its vectorial capacity to transmit various arboviruses such as Zika, yellow fever, dengue, and chikungunya. In California, its expanding geographic distribution has been unrestrained. This urgently calls for innovative tools such as the use of sterile insect technique (SIT) to strengthen invasive control.
View Article and Find Full Text PDFAnnealing Study on Praseodymium-Doped Indium Zinc Oxide Thin-Film Transistors and Fabrication of Flexible Devices.
Micromachines (Basel)
December 2024
Guangdong Basic Research Center of Excellence for Energy & Information Polymer Materials, State Key Laboratory of Luminescent Materials and Devices, School of Materials Sciences and Engineering, South China University of Technology, Guangzhou 510640, China.
The praseodymium-doped indium zinc oxide (PrIZO) thin-film transistor (TFT) is promising for applications in flat-panel displays, due to its high carrier mobility and stability. Nevertheless, there are few studies on the mechanism of annealing on PrIZO films and the fabrication of flexible devices. In this work, we first optimized the annealing-process parameters on the glass substrate.
View Article and Find Full Text PDFCapacity Planning (Capital, Staff and Costs) of Inpatient Maternity Services: Pitfalls for the Unwary.
Int J Environ Res Public Health
January 2025
Healthcare Analysis and Forecasting, Wantage OX12 0NE, UK.
This study investigates the process of planning for future inpatient resources (beds, staff and costs) for maternity (pregnancy and childbirth) services. The process of planning is approached from a patient-centered philosophy; hence, how do we discharge a suitably rested healthy mother who is fully capable of caring for the newborn baby back into the community? This demonstrates some of the difficulties in predicting future births and investigates trends in the average length of stay. While it is relatively easy to document longer-term (past) trends in births and the conditions relating to pregnancy and birth, it is exceedingly difficult to predict the future nature of such trends.
View Article and Find Full Text PDFFunctionalized UiO-66 induces shallow electron traps in heterojunctions with InN for enhanced photocathodic water splitting.
J Colloid Interface Sci
January 2025
State Key Laboratory of Luminescent Materials and Devices, South China University of Technology, Guangzhou 510640 China; School of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 China. Electronic address:
Indium nitride (InN) exhibited significant potential as a photoelectrode material for photoelectrochemical (PEC) water splitting, attributed to its superior light absorption, high electron mobility, and direct bandgap. However, its practical application was constrained by rapid carrier recombination occurring within the bulk and at the surface. To address these limitations, researchers developed InN/UiO-66 heterojunction photoelectrodes, which markedly enhanced PEC water splitting for hydrogen production.
View Article and Find Full Text PDFEnhanced Efficiency and Stability in Blade-Coated Perovskite Solar Cells through Using 2,3,4,5,6-Pentafluorophenylethylammonium Halide Additives.
ACS Appl Mater Interfaces
January 2025
Centre for Organic Photonics & Electronics, School of Chemistry and Molecular Biosciences, The University of Queensland, Brisbane, Queensland 4072, Australia.
The power conversion efficiency (PCE) of perovskite solar cells is sensitive to their method of fabrication as well as the combination of materials in the perovskite layer. Air knife-assisted blade coating enables good quality perovskite films to be formed but the device efficiencies still tend to lag behind those fabricated using spin-coated perovskite layers. Herein we report the use of three 2,3,4,5,6-pentafluorophenylethylammonium halides (FEAX, where X = I, Br or Cl) as additives in nitrogen knife-assisted blade-coated methylammonium lead iodide (MAPbI) perovskite solar cells.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!