Gel formulations containing the local anesthetic butamben (BTB) encapsulated in either conventional (BTBLUV) or elastic (BTBLUV-EL) liposomes were prepared and characterized, and then evaluated in terms of their skin permeability. Parameters measured included vesicle size and surface charge, BTB fluorescence anisotropy, encapsulation efficiency, partition coefficient and liposomal membrane organization. Encapsulation efficiencies and membrane/water partition coefficients were determined using a phase separation. The partition coefficients of the elastic and conventional formulations were 2025 ± 234 and 1136 ± 241, respectively. The sizes of the elastic and conventional liposomes did not change significantly (p > 0.05) following incorporation of the anesthetic. As expected, the elastic liposomes presented order parameters that were lower than those of the conventional liposomes, as determined by electron paramagnetic resonance with a 5-stearic acid nitroxide probe incorporated into the bilayer. After 8 h, the fluxes into the receiving solution (µg/cm(2)/h) were 6.95 ± 1.60 (10% BTB), 23.17 ± 6.09 (10% BTBLUV) and 29.93 ± 6.54 (10% BTBLUV-EL). The corresponding time lags (h) were 1.90 ± 0.48, 1.23 ± 0.28 and 1.57 ± 0.38, respectively. The permeability coefficients (10(-3 )cm/h) were 1.02 ± 0.23, 2.96 ± 0.77 and 4.14 ± 0.9, for 10% BTB, 10% BTBLUV and 10% BTBLUV-EL, respectively. The results demonstrate that anesthetic access through the skin can be considerably enhanced using liposomal gel formulations, compared to plain gel formulations.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.3109/08982104.2013.796975 | DOI Listing |
Magn Reson Med
January 2025
MRI Research Centre, Physics, University of New Brunswick, Fredericton, New Brunswick, Canada.
Purpose: Magnetic resonance elastography (MRE) provides detailed maps of tissue stiffness, helping to diagnose various health conditions, but requires the use of expensive clinical MRI scanners. Our approach utilizes compact, cost-effective portable MR sensors that offer bulk characterization of material properties in a region of interest close to the surface (within 1-2 cm). This accessible instrument could enable routine monitoring and prevention of diseases not readily evaluated with conventional tools.
View Article and Find Full Text PDFAcad Radiol
January 2025
Department of Radiology, Washington University School of Medicine, 510 S. Kingshighway Blvd, St. Louis, MO 63110 (S.I., M.A.T., M.I., C.S., R.L., A.H., R.L.W., T.J.F.). Electronic address:
Rationale And Objective: Conventional positron emission tomography (PET) respiratory gating utilizes a fraction of acquired PET counts (i.e., optimal gate [OG]), whereas elastic motion correction with deblurring (EMCD) utilizes all PET counts to reconstruct motion-corrected images without increasing image noise.
View Article and Find Full Text PDFJ Funct Biomater
January 2025
Department of Conservative Dentistry, School of Dentistry, Kyung Hee University, Seoul 02447, Republic of Korea.
To overcome limitations of dentin bonding due to collagen degradation at a bonded interface, incorporating bioactive glass (BAG) into dentin adhesives has been proposed to enhance remineralization and improve bonding durability. This study evaluated sol-gel-derived BAGs (BAG79, BAG87, BAG91, and BAG79F) and conventional melt-quenched BAG (BAG45) incorporated into dentin adhesive to assess their remineralization and mechanical properties. The BAGs were characterized by using field-emission scanning electron microscopy (FE-SEM) and transmission electron microscopy for surface morphology.
View Article and Find Full Text PDFGels
January 2025
Department of Mechanical and Aerospace Engineering, University of Houston, Houston, TX 77204, USA.
Stimuli-responsive hydrogels hold immense promise for biomedical applications, but conventional gelation processes often struggle to achieve the precision and complexity required for advanced functionalities such as soft robotics, targeted drug delivery, and tissue engineering. This study introduces a class of 3D-printable magnetic hydrogels with tunable stiffness, adhesion, and magnetic responsiveness, prepared through a simple and efficient "one-pot" method. This approach enables precise control over the hydrogel's mechanical properties, with an elastic modulus ranging from 43 kPa to 277 kPa, tensile strength from 93 kPa to 421 kPa, and toughness from 243 kJ/m to 1400 kJ/m, achieved by modulating the concentrations of acrylamide (AM) and FeO nanoparticles.
View Article and Find Full Text PDFDent J (Basel)
December 2024
Faculty of Dental Medicine, Grigore T. Popa University of Medicine and Pharmacy Iasi, Str. Universitatii No. 16, 700115 Iasi, Romania.
: The aim of this study was to evaluate the influence of acidic beverages on the mechanical properties of various dental resin-based materials. : A total number of 160 samples were prepared using four types of resin-based materials-Group A ( = 40): flowable composite, Group B ( = 40): heavy-flow composite, Group C ( = 40): resin-based sealant and Group D ( = 40): nano-hybrid composite. Then, the samples were distributed into four subgroups according to the submersion solution: ( = 10): artificial saliva, ( = 10): coffee, ( = 10): cola and ( = 10): red wine.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!