Objectives: To determine the effect on resin composite-to-dentin bond strength of incorporation of an acidic tin-chloride pretreatment in two adhesive systems.
Materials And Methods: Human molars were ground to expose mid-coronal dentin. For microtensile bond strength (μTBS) testing, dentin was treated with Optibond FL or Clearfil SE according to one of six protocols (n = 22/group). Group 1: Phosphoric acid etching, Optibond FL Prime, Optibond FL Adhesive (manufacturer's instructions; control); Group 2: Tin-chloride pretreatment, Optibond FL Prime, Optibond FL Adhesive; Group 3: Phosphoric acid etching, tin-chloride pretreatment, Optibond FL Prime, Optibond FL Adhesive; Group 4: Clearfil SE Primer, Clearfil SE Bond (manufacturer's instructions; control); Group 5: Phosphoric acid etching, Clearfil SE Primer, Clearfil SE Bond; and Group 6: Tin-chloride pretreatment, Clearfil SE Primer, Clearfil SE Bond. The molars were then built up with resin composite (Clearfil Majesty Esthetic). After storage (1 week, 100 % humidity, 37 °C) the μTBS was measured and failure mode was determined. Additionally, pretreated dentin surfaces were evaluated using SEM and EDX. The μTBS results were analyzed statistically by a Welch Two Sample t-test and a Kruskal-Wallis test followed by exact Wilcoxon rank sum tests with Bonferroni-Holm adjustment for multiple testing (α = 0.05).
Results: When Optibond FL was used, partial or total replacement of phosphoric acid with tin-chloride decreased μTBS significantly. In contrast, when Clearfil SE was used, inclusion of a tin-chloride pretreatment in the adhesive procedure increased μTBS significantly.
Conclusions: Tin-chloride pretreatment had a beneficial influence on the bond promoting capacity of the MDP-containing adhesive system Clearfil SE.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1007/s00784-013-0975-6 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
L-Poly(lactic acid) Production by Microwave Irradiation of Lactic Acid Obtained from Lignocellulosic Wastes.
Int J Mol Sci
June 2023
Research Institute for Analytical Instrumentation Subsidiary, National Institute for Research and Development of Optoelectronics Bucharest INOE 2000, 67 Donath Street, 400293 Cluj-Napoca, Romania.
L-polylactic acid (PLA), a semi-crystalline aliphatic polyester, is one of the most manufactured biodegradable plastics worldwide. The objective of the study was to obtain L-polylactic acid (PLA) from lignocellulosic plum biomass. Initially, the biomass was processed via pressurized hot water pretreatment at a temperature of 180 °C for 30 min at 10 MPa for carbohydrate separation.
View Article and Find Full Text PDFProtective effect of tin chloride on rhabdomyolysis-induced acute kidney injury in rats.
PLoS One
May 2022
Department of Anesthesiology and Resuscitology, Okayama University Graduate School of Medicine, Dentistry and Pharmaceutical Sciences, Okayama, Japan.
The heme component of myoglobin plays a crucial role in the pathogenesis of rhabdomyolysis-associated acute kidney injury (RM-AKI). Heme oxiganenase-1 (HO-1) is the rate-limiting enzyme of heme catabolism, and its metabolites, iron, biliverdin, and carbon monoxide, have antioxidant properties. Tin chloride (SnCl2) is a kidney specific HO-1 inducer.
View Article and Find Full Text PDFProtective Effect of Solutions Containing Polymers Associated with Fluoride and Stannous Chloride on Hydroxyapatite Dissolution.
Caries Res
May 2021
Department of Restorative Dentistry, Institute of Science and Technology, São Paulo State University, UNESP, São José dos Campos, Brazil,
This study investigated the protective effect of experimental solutions containing 4 polymers (polyoxirane, hydroxypropylmethylcellulose [HPMC], pectin, and an amino methacrylate copolymer [AMC]) in 2 concentrations (low and high) associated or not with sodium fluoride (F; 225 ppm F-) or sodium fluoride plus stannous chloride (FS; 800 ppm Sn2+) on the dissolution of hydroxyapatite crystals (HA). Deionized water was the control. The pretreated HA was added to a 0.
View Article and Find Full Text PDFThe Effect of SnCl/AmF Pretreatment on Short- and Long-Term Bond Strength to Eroded Dentin.
Biomed Res Int
October 2018
Department of Preventive, Restorative, and Pediatric Dentistry, School of Dental Medicine, University of Bern, Freiburgstrasse 7, 3010 Bern, Switzerland.
This study investigated the effect of SnCl/AmF pretreatment on short- and long-term bond strength of resin composite to eroded dentin mediated by two self-etch, MDP-containing adhesive systems. 184 dentin specimens were produced from extracted human molars. Half the specimens ( = 92) were artificially eroded, and half were left untreated.
View Article and Find Full Text PDFImparting functionality viz color, antioxidant and antibacterial properties to develop multifunctional wool with Tectona grandis leaves extract using reflectance spectroscopy.
Int J Biol Macromol
April 2018
Department of Chemistry, Jamia Millia Islamia (Central University), New Delhi, 110025, India. Electronic address:
In recent years, considerable attention has been given to plant colorants for use in dyeing applications because of their newly discovered properties such as insect repellency, deodorizing, antioxidant, sun protection, and antibacterial activity. In view of their better biocompatibility, biodegradability, less-toxicity, natural colorants are gaining worldwide interest for producing elegant hues and highly functional value-added textiles. In the present work, we investigated the coloring and functional finishing of wool with Tectona grandis L.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!