A method is introduced to measure friction on small, free standing objects, specifically microfabricated silicon plates, based on atomic force microscopy (AFM). An AFM tip is brought into contact with the plate resting on a substrate. The substrate is displaced laterally and, provided the AFM tip does not slide over the plate, the twisting of the AFM cantilever is used to measure the friction of the underlying plate-substrate interface. The method can measure nano-Newton to micro-Newton forces (both friction and applied load) and provides a means to measure friction of macroscopic structures at low load.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1063/1.4773534 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Exploration of low-sulfonate lignin electrospinning conditions for the development of new renewable lubricant formulations.
Nanoscale
January 2025
Pro2TecS - Chemical Product and Process Technology Research Center. Department of Chemical Engineering and Materials Science. Universidad de Huelva. ETSI, Campus de "El Carmen", 21071 Huelva, Spain.
This study explores the preparation of lubricating oleo-dispersions using electrospun nanofibrous mats made from low-sulfonate lignin (LSL) and polycaprolactone (PCL). The rheological and tribological properties of the oleo-dispersions were significantly modulated for the first time through the exploration of LSL/PCL ratio and electrospinning conditions such as applied voltage, distance between the tip and collector, flow rate, ambient humidity, and collector configuration. Adequate uniform ultrathin fibers and Small-amplitude oscillatory shear (SAOS) functions of the oleo-dispersions, with storage modulus values ranging from 10 to 10 Pa at 25 °C, were obtained with a flow rate of 0.
View Article and Find Full Text PDFSensorless model-based tension control for a cable-driven exosuit.
Wearable Technol
December 2024
Sensory Motor Systems Lab, Department of Health Sciences and Technology, ETH Zürich, Zürich, Switzerland.
Cable-driven exosuits have the potential to support individuals with motor disabilities across the continuum of care. When supporting a limb with a cable, force sensors are often used to measure tension. However, force sensors add cost, complexity, and distal components.
View Article and Find Full Text PDF[Determination of physical properties and calibration of discrete element simulation parameters for Jianwei Xiaoshi Granules].
Zhongguo Zhong Yao Za Zhi
December 2024
Key Laboratory of Modern Preparations of Traditional Chinese Medicine, Ministry of Education, Jiangxi University of Chinese Medicine Nanchang 330004, China National Key Laboratory of Creation of Modern Chinese Medicine with Classical Formulas Nanchang 330004, China Jiangxi Technology Innovation Center of Green Manufacturing of Chinese Medicine Nanchang 330004, China.
The construction method and simulation parameter settings for the discrete element model of Jianwei Xiaoshi Granules, as the primary material of Jianwei Xiaoshi Tablets, are not yet clear. The accuracy of the simulation model significantly influences the dynamic response characteristics between granules. Therefore, it is necessary to calibrate the parameters to improve the accuracy of the simulation parameters.
View Article and Find Full Text PDFRelationship Between Physical Characteristics of Cereal Polysaccharides and Soft Tribology-The Importance of Grain Source and Malting Modification.
Food Sci Nutr
January 2025
Technical University of Munich, TUM School of Life Sciences, Chair of Brewing and Beverage Technology, Group Raw Material Based Brewing and Beverage Technology Freising Germany.
Starch and non-starch polysaccharides ((N)SPs) are relevant in cereal-based beverages. Although their molar mass and conformation are important to the sensory characteristics of beer and non-alcoholic beer, their triggering mechanism in the mouth is not fully understood. Soft tribology has emerged as a tool to mimic oral processing (drinking).
View Article and Find Full Text PDFMolecular-Scale Simulation of Wetting of Actin Filaments by Protein Droplets.
J Phys Chem B
January 2025
Department of Computer and Information Sciences, Department of Materials Science and Engineering, University of Delaware, Newark, Delaware 19716, United States.
Liquid phase-separating proteins can form condensates that play an important role in spatial and temporal organization of biological cells. The understanding of the mechanisms that lead to the formation of protein condensates and their interactions with other biomolecules may lead to processing routes for soft materials with tailored geometry and function. Fused in sarcoma (FUS) is an example of a nuclear protein that forms stable complexes, and recent studies have highlighted its ability to wet actin filaments and bundle them into networks.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!