Purpose: Descemet stripping automated endothelial keratoplasty (DSAEK) has its own set of complications including interface abnormalities. This case series presents the largest number of patients who developed textural interface opacity (TIO) at the graft-host interface after DSAEK.
Methods: This is a retrospective multicenter case series of 30 patients from 7 institutions with the finding of TIO. Clinical information collected included donor preparation details, recipient information, and surgical technique. Clinical outcomes included best-corrected visual acuity and status of TIO appearance at the last follow-up visit. Slit-lamp photographs were analyzed and compared.
Results: The majority of the patients (73%) had a best-corrected visual acuity of 20/40 or better. Four of the donor tissues were prepared with a microkeratome blade with the same lot number. Six patients had a central interface space between host and donor stromal surfaces--presumed interface fluid but potentially viscoelastic. A slight majority (57%) of patients had improvement in the severity of TIO, with 20% noted to have a complete resolution of TIO (mean follow-up of 11.9 months). Two clinical types of TIO were seen: an elongated type and a punctate type.
Conclusions: Most patients with TIO after DSAEK obtain good visual outcomes. TIO spontaneously improves or even resolves during follow-up without intervention. The etiology of this condition is unknown, but we propose 2 different mechanisms. The elongated type could be secondary to an irregular cut of the donor with the microkeratome blade. The punctate type may be secondary to retained viscoelastic.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1097/ICO.0b013e31826429d5 | DOI Listing |
Food Chem
January 2025
Department of Food Science, College of Food Science and Engineering, Jilin University, Changchun 130062, China. Electronic address:
Using of low-fat emulsion gels stabilized by quinoa protein (QP) for 3D food printing was limited by their defective rheological properties. The study was to explore the feasibility of using fucoidan (FU) to improve the printability and curcumin encapsulation stability of QP emulsion gel. The gels with 0.
View Article and Find Full Text PDFMaterials (Basel)
December 2024
State Key Laboratory of Roll Composite Materials, Sinosteel Xing Tai Mechanical Roll Co., Ltd., No. 1 Xinxing West Street, Xingtai 054000, China.
Composite roll produced through casting methods typically remain in the as-cast state after forming. During the preparation process, extended exposure to high temperatures often results in microstructural coarsening at the interface and surface layers, restricting their mechanical performance. To overcome this limitation, we developed a novel vacuum billet forging process for the fabrication of composite rolls.
View Article and Find Full Text PDFExposure to ambient particulate matter (PM) with an aerodynamic diameter of <10 μm (PM) is a well-established health hazard. There is increasing evidence that geogenic (Earth-derived) particles can induce adverse biological effects upon inhalation, though there is high variability in particle bioreactivity that is associated with particle source and physicochemical properties. In this study, we investigated physicochemical properties and biological reactivity of volcanic ash from the April 2021 eruption of La Soufrière volcano, St.
View Article and Find Full Text PDFPolymers (Basel)
December 2024
Institute of Machine Design and Tribology (IMKT), Leibniz University Hannover, An der Universität 1, 30823 Garbsen, Germany.
To enhance the sliding tribological performance between PTFE and 40#steel (AISI 1040) under full film lubrication conditions, laser surface texturing (LST) technology was employed to prepare micro-dimples on the contact surfaces of 40# steel discs. The Box-Behnken design response surface methodology (BBD-RSM) was applied to optimize the micro-dimple parameters. Coefficients of friction (COFs), wear losses and worn contact surfaces of the PTFE-40# steel tribo-pairs were researched through repeated wear tests, as lubricated with sufficient anti-wear hydraulic oil.
View Article and Find Full Text PDFMolecules
December 2024
IMT Atlantique, GEPEA, UMR CNRS 6144, F-44307 Nantes, France.
The textural properties of synthetic and natural clays in the sodium form and exchanged with tetramethylammonium cations (TMA) were characterized using N and Ar physisorption isotherms at cryogenic temperatures. Specific surface areas and micro/mesoporous volumes were determined using the BET and the models. The analysis requires the use of reference isotherms measured at the same temperature on the surface of non-porous materials with an identical chemical composition.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!