The interaction of glycerol concentrations of 0-10% and cooling rates from 1 to 1,500 degrees C/min with boar spermatozoa motility and acrosomal integrity (proportion of spermatozoa with normal apical ridge) was studied after thawing 0.5 ml straws at a constant rate. While increasing the glycerol concentration from 0 to 4% progressively improved motility, the percentage of spermatozoa with a normal apical ridge gradually decreased. The magnitudes of the respective changes depended on cooling rate. A peak value of 48.1% and rating 3.8 were obtained in semen protected with 4% glycerol, frozen at 30 degrees C/min. Increasing the glycerol levels above 6% resulted in a gradual decrease in motility. The proportion of spermatozoa with normal apical ridge was highest in semen protected with 0-1% glycerol after cooling at 30 degrees C/min (64.4% and 66.1%, respectively), but at these glycerol concentrations the percentage of motile spermatozoa was low. At the 30 degrees C/min cooling rate, the decline in the proportion of cells with normal apical ridge due to increasing the glycerol levels to 3 and 4% was relatively slow (57.3% and 49.4%, respectively). Cooling at 1 degrees C/min was detrimental to acrosomal integrity, which decreased with increasing glycerol concentration, in contrast to increasing motility, which even at its maximum, remained low. The direct plunging of straws into liquid nitrogen (1,500 degrees C/min) resulted in damaged acrosomes in all spermatozoa with the total loss of motility. Balancing motility and acrosomal integrity, freezing boar semen protected with 3% glycerol by cooling at 30 degrees C/min resulted in optimal survival for boar semen frozen in 0.5 ml French straws.

Download full-text PDF

Source
http://dx.doi.org/10.1002/mrd.1080250204DOI Listing

Publication Analysis

Top Keywords

degrees c/min
28
acrosomal integrity
16
normal apical
16
apical ridge
16
increasing glycerol
16
glycerol concentration
12
motility acrosomal
12
spermatozoa normal
12
semen protected
12
cooling degrees
12

Similar Publications

In this study, three stainless steel materials (17-4PH, 316L, and 304) were experimentally simulated using metal injection molding (MIM) technology to explore the size shrinkage behavior and defect formation mechanism of materials with different particle sizes during sintering. The sintering environment was linearly heated to 1250 °C at a rate of 5 °C/min and kept warm for 90 min. Multi-physics field coupling analysis was performed using ANSYS Workbench software.

View Article and Find Full Text PDF

Thermal Stability and Purity of Graphene and Carbon Nanotubes: Key Parameters for Their Thermogravimetric Analysis (TGA).

Nanomaterials (Basel)

October 2024

Institut de Ciència de Materiales de Barcelona (ICMAB-CSIC), Campus de la UAB, Bellaterra, 08193 Barcelona, Spain.

Article Synopsis
  • Thermal analysis, using techniques like thermogravimetric analysis (TGA), is essential for characterizing the physicochemical properties of nanomaterials, especially carbon nanomaterials such as carbon nanotubes (CNTs) and graphene.
  • TGA helps determine sample quality, stability, impurity presence, and functionalization degree, and it also assesses thermal stability against oxidation, which can be improved through purification and nitrogen doping.
  • The study emphasizes the importance of key parameters like gas flow rate, sample weight, and heating rate in TGA, finding that higher heating rates significantly increase the oxidation onset temperature of CNTs and recommending optimal parameters for accurate analysis.
View Article and Find Full Text PDF
Article Synopsis
  • The study focuses on using the heat from cooled iron ore pellets to produce metallized pellets for steelmaking without CO emissions, by reducing the pellets in hydrogen during cooling.
  • As the cooling rate decreases, improvements are seen in iron content and metallization, while compressive strength first increases and then drops significantly.
  • The cooling rate affects the particles' morphology and porosity, leading to larger, uniformly distributed metallic iron particles, with the optimal cooling rate of 3.7 °C/min providing a good balance of metallization and compressive strength.
View Article and Find Full Text PDF

Effects of temperature on transient neurologic dysfunction after total arch replacement.

Gen Thorac Cardiovasc Surg

August 2024

Department of Cardiovascular Surgery, Sapporo Medical University School of Medicine, S1W16 Chuo-ku, Sapporo, Hokkaido, 060-8543, Japan.

Article Synopsis
  • The study examines the impact of cooling status during aortic surgery on the risk of transient neurologic dysfunction in patients undergoing total arch replacement.
  • It analyzes data from surgeries conducted between December 2011 and January 2021, focusing on various parameters such as cooling speed and the cooling area.
  • Findings suggest that both a larger cooling area and a faster cooling speed are linked to a higher incidence of transient neurologic dysfunction, indicating that excessive or rapid cooling could lead to brain injury.
View Article and Find Full Text PDF

In recent years, various kinds of civil explosive detonation accidents have occurred frequently around the world, resulting in substantial human casualties and significant property losses. It is generally believed that thermal stimulation plays a critical role in triggering the detonation of explosives; consequently, the study of the thermal hazards of explosives is of great significance to many aspects of safety emergency management practices in the production, transportation, storage, and use of explosives. It is known that the thermal stability of the ammonium perchlorate-aluminium system and the ammonium nitrate-aluminium system has been extensively investigated previously in the literature.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!