Objective: Previous studies of English-speaking esophageal (SE) and tracheoesophageal (TE) speakers revealed a significantly lower voice fundamental frequency (F0) than normal laryngeal (NL) speakers. Studies of SE and TE speakers of a tone language, however, indicated discrepant findings. Tonal SE and TE speakers could produce comparable or even higher F0 than NL speakers. The present study examined the F0 characteristics associated with speech and nonspeech tasks produced by Cantonese SE and TE speakers.
Subjects And Methods: Speech produced by 15 superior SE, 15 superior TE and 15 NL speakers was recorded while each was reading a short passage and performing a pitch scaling task. F0 values were calculated from the speech samples.
Results: SE speakers had higher average F0 in reading tasks than TE and NL speakers, while the NL speakers exhibited the highest average F0 values followed by SE and TE speakers during pitch scaling. In addition, pitch scaling (nonspeech) tasks were associated with higher average F0 than passage reading tasks regardless of speaker type.
Conclusion: The findings point to the fact that, despite the use of the new sound source, SE and TE speakers were still able to change F0 for specific speech tasks.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1159/000342825 | DOI Listing |
Polymers (Basel)
January 2025
Department of Mechanical Engineering, University of Massachusetts Lowell, Lowell, MA 01854, USA.
This study presents the design, modeling, and validation of a mixing screw for energy-efficient single-screw extrusion. The screw features a short length-to-diameter (L/D) ratio of 8:1 and incorporates double flights with variable pitch and counter-rotating mixing slots. These features promote enhanced plastication by breaking up the solid bed and improving thermal homogeneity through backflow mechanisms relieving a 3.
View Article and Find Full Text PDFMicromachines (Basel)
January 2025
DTU Nanolab, National Centre for Nano Fabrication and Characterization, Technical University of Denmark, Ørsteds Plads B347, 2800 Kongens Lyngby, Denmark.
A wafer-scale process for fabricating monolithically suspended nano-perforated membranes (NPMs) with integrated support structures into silicon is developed. Existing fabrication methods are suitable for many desired geometries, but face challenges related to mechanical robustness and fabrication complexity. We demonstrate a process that utilizes the cyclic deposit, remove, etch, and multi-step (DREM) process for directional etching of high-aspect-ratio (HAR) 300 nm in diameter nano-pores of 700 nm pitch.
View Article and Find Full Text PDFMicromachines (Basel)
January 2025
Faculty of Mechanical Engineering and Design, Kaunas University of Technology, 51424 Kaunas, Lithuania.
In recent years, microfluidics has emerged as an interdisciplinary field, receiving significant attention across various biomedical applications. Achieving a noticeable mixing of biofluids and biochemicals at laminar flow conditions is essential in numerous microfluidics systems. In this research work, a new kind of micromixer design integrated with an Archimedes screw is designed and investigated using numerical simulation and experimental approaches.
View Article and Find Full Text PDFLangmuir
January 2025
Brigham Young University, Provo, Utah 84602, United States.
Accurate models for predicting drop dynamics, such as maximum drop departure sizes, are crucial for estimating heat transfer rates during condensation on superhydrophobic (SH) surfaces. Previous studies have focused on examining the heat transfer rates for SH surfaces under the influence of gravity or vapor flowing over the surface. This study investigates the impact of surface solid fraction and texture scale on drop mobility in a condensing environment with a humid air flow.
View Article and Find Full Text PDFEur J Med Res
January 2025
National Center for Orthopaedics, Shanghai Sixth People's Hospital, 600 Yishan Road, Xuhui District, Shanghai, 200233, China.
Background: Scarf osteotomy is a well-established procedure for hallux valgus, yet recurrence rates range from 3.6% to 10%. Pes planus, which often coexisting with hallux valgus, is a risk factor for recurrence.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!