In the development of artificial cancellous bones, two major factors need to be considered: the integrity of the overall structure and its permeability. Whilst there have been many studies analysing the mechanical properties of artificial and natural cancellous bones, permeability studies, especially those using numerical simulation, are scarce. In this study, idealised cancellous bones were simulated from the morphological indices of natural cancellous bone. Three different orientations were also simulated to compare the anisotropic nature of the structure. Computational fluid dynamics methods were used to analyse fluid flow through the cancellous structures. A constant mass flow rate was used to determine the intrinsic permeability of the virtual specimens. The results showed similar permeability of the prismatic plate-and-rod model to the natural cancellous bone. The tetrakaidecahedral rod model had the highest permeability under simulated blood flow conditions, but the plate counterpart had the lowest. Analyses on the anisotropy of the virtual specimens showed the highest permeability for the horizontal orientation. Linear relationships were found between permeability and the two physical properties, porosity and bone surface area.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1016/j.medengphy.2012.08.011 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Chemerin mediates exercise-induced improvements of bone microstructure and bone mass in diabetes or high fat diet mice.
Mol Cell Endocrinol
January 2025
Shanghai University of Sport, School of Health and Exercise, Shanghai 200438, China. Electronic address:
To clarify the roles and mechanisms of adipokine chemerin in exercise-induced bone improvements in type 2 diabetes mellitus (DM) mice and mice fed on high fat diet (HFD). DM mice were established by HFD+streptozotocin injection, exogenous chemerin was supplemented prior to running, and found that exogenous chemerin reversed 6-week exercise-induced improvements in cancellous bone parameters in DM mice. While adipose-specific chemerin knockout improved microstructure and mass of cancellous bone in HFD mice and further increased exercise-induced bone improvements, accompanied with promoted osteogenesis and inhibited osteoclasis represented as the changes of RANKL, M-CSF, Runx2, Osterix, OPG, ALP and CTSK.
View Article and Find Full Text PDF3D bio-printed proteinaceous bioactive scaffold loaded with dual growth factor enhanced chondrogenesis and in situ cartilage regeneration.
Bioact Mater
April 2025
Department of Regenerative Medicine, College of Medicine, Soonchunhyang University, Cheonan, Republic of Korea.
Articular cartilage has a limited self-healing capacity, leading to joint degeneration and osteoarthritis over time. Therefore, bioactive scaffolds are gaining attention as a promising approach to regenerating and repairing damaged articular cartilage through tissue engineering. In this study, we reported on a novel 3D bio-printed proteinaceous bioactive scaffolds combined with natural porcine cancellous bone dECM, tempo-oxidized cellulose nanofiber (TOCN), and alginate carriers for TGF-β1, FGF-18, and ADSCs to repair cartilage defects.
View Article and Find Full Text PDFUniversal Hydrogel Carrier Enhances Bone Graft Success: Preclinical and Clinical Evaluation.
Adv Healthc Mater
January 2025
School of Chemical and Biomolecular Engineering, The University of Sydney, Sydney, NSW, 2006, Australia.
Orthopedic, maxillofacial, and complex dentoalveolar bone grafting procedures that require donor-site bone harvesting can be associated with post-surgical complications. There has been widespread adoption of exogenously sourced particulate bone graft materials (BGM) for bone regenerative procedures; however, the particulate nature of these materials may lead to compromised healing outcomes, mainly attributed to structural collapse of the BGM, prolonged tissue healing. In this study, a fully synthetic thermoresponsive hydrogel-based universal carrier matrix (TX) that forms flowable and shapable putties with different BGMs while spatially preserving the particles in a 3D scaffold at the implantation site is introduced.
View Article and Find Full Text PDFFunctional hydrogel empowering 3D printing titanium alloys.
Mater Today Bio
February 2025
Department of Orthopedics, The Second Hospital of Jilin University, Changchun, 130041, Jilin, China.
Titanium alloys are widely used in the manufacture of orthopedic prosthesis given their excellent mechanical properties and biocompatibility. However, the primary drawbacks of traditional titanium alloy prosthesis are their much higher elastic modulus than cancellous bone and poor interfacial adhesion, which lead to poor osseointegration. 3D-printed porous titanium alloys can partly address these issues, but their bio-inertness still requires modifications to adapt to different physiological and pathological microenvironments.
View Article and Find Full Text PDFComparative study of arthroscopic autologous cancellous bone grafting and medial malleolar osteotomy combined with autologous periosteal iliac bone grafting for the treatment of osteochondral lesions of the talus.
J Orthop Surg Res
January 2025
Department of Sports Medicine, The Affiliated Hospital of Qingdao University, Qingdao University, Qingdao, Shandong, 266071, P. R. China.
Background: Surgical management methods for Hepple IV-V osteochondral lesions of the talus (OLT) are diverse. This study aimed to compare the clinical efficacy of arthroscopic autologous cancellous bone grafting and medial malleolar osteotomy combined with autologous periosteal iliac bone grafting in the treatment of medial Hepple IV-V OLT.
Methods: A retrospective analysis of clinical data from patients who underwent surgical treatment for Hepple IV-V OLT (2020-2023) was conducted.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!