The effect of degree of compression on the evolution of tablet microstructure and bond probability during compression of granular solids has been studied. Microcrystalline cellulose pellets of low (about 11%) and of high (about 32%) porosity were used. Tablets were compacted at 50, 100 and 150 MPa applied pressures and the degree of compression and the tensile strength of the tablets determined. The tablets were subjected to mercury intrusion measurements and from the pore size distributions, a void diameter and the porosities of the voids and the intra-granular pores were calculated. The pore size distributions of the tablets had peaks associated with the voids and the intra-granular pores. The void and intra-granular porosities of the tablets were dependent on the original pellet porosity while the total tablet porosity was independent. The separation distance between pellets was generally lower for tablets formed from high porosity pellets and the void size related linearly to the degree of compression. Tensile strength of tablets was higher for tablets of high porosity pellets and a scaled tablet tensile strength related linearly to the degree of compression above a percolation threshold. In conclusion, the degree of compression controlled the separation distance and the probability of forming bonds between pellets in the tablet.

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.ijpharm.2012.08.011DOI Listing

Publication Analysis

Top Keywords

degree compression
24
tensile strength
12
granular solids
8
microstructure bond
8
bond probability
8
tablets
8
compression tensile
8
strength tablets
8
pore size
8
size distributions
8

Similar Publications

Cervical plexus block (CPB), like other types of regional anesthesia, represents an alternative anesthetic technique in those cases where the performance of general anesthesia (GA) carries an increased risk both for the patient and the outcome of the operative treatment. It has traditionally been used for years in carotid surgery as an alternative to GA, especially due to the possibility of superior monitoring - the awake patient. However, its effectiveness has been proven in other types of neck surgery, primarily in thyroid surgery, neck dissections, tracheostomy, central venous catheter insertion, clavicle surgery, etc.

View Article and Find Full Text PDF

Zonal Characteristics of Collagen Ultrastructure and Responses to Mechanical Loading in Articular Cartilage.

Acta Biomater

January 2025

Biomedical Engineering, College of Engineering, Mathematics and Physical Sciences, University of Exeter, UK. Electronic address:

The biomechanical properties of articular cartilage arise from a complex bioenvironment comprising hierarchically organised collagen networks within the extracellular matrix (ECM) that interact with the proteoglycan-rich interstitial fluid. This network features a depth-dependent fibril organisation across different zones. Understanding how collagen fibrils respond to external loading is key to elucidating the mechanisms behind lesion and managing degenerative conditions like osteoarthritis.

View Article and Find Full Text PDF

Extensive congenital pulmonary airway malformation (CPAM) of the left fetal lung and associated marked dextroposition of the fetal heart were noted at 21 weeks' gestation. The right fetal lung appeared compressed with the cardiomediastinal shift angle measuring approximately 20 degrees. Potential subsequent right pulmonary hypoplasia was considered.

View Article and Find Full Text PDF

Purpose: The present study aims at exploring the effect of pitch, loudness, vowel, and voice condition on supraglottic activity among female participants with voice disorders and among female participants with normal voices.

Methods: Forty-four volunteers were recruited. Inclusion criteria for the dysphonic group were: 1) age between 20 and 50 years, 2) reporting at least 1 year-long history of voice problems, 3) moderate or severe dysphonia.

View Article and Find Full Text PDF

An innovative modeling approach for the simulative description of the part quality of rubber materials, including the processing history, is presented in this paper. This modeling approach, the so-called average curing speed (ACS) model, is based on the degree of cure and the average curing speed instead of the conventionally considered temperature approach. Such approach neglects the processing history by calculating only the degree of cure.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!