Objective: This study was undertaken to assess the effect of enamel deproteinization with 5.25% sodium hypochlorite (NaOCl) before phosphoric acid (H3PO4) etching on the shear bond strength ofAdperTM Single Bond 2 adhesive and Filtek Z-350 XT composite resin.
Study Design: Forty human sound permanent molars which were extracted for periodontal reasons were used in the experimental protocol as under: Group-A (20 teeth):-A 5X4 mm window of the enamel surface was etched with 37% H3PO4 gel for 15 seconds, washed with distilled water and air dried. A single coat of Adper Single Bond 2 adhesive was applied and photo polymerized for 20 seconds and Filtek Z-350 XT composite resin block of length 5 mm, width 4 mm and height 5mm respectively was built and photo polymerized in increments for 20 seconds each. Group-B (20 teeth):--Similarly the enamel surface was treated with 5.25% NaOCl for 60 seconds, washed with distilled water and then etched with 37% H3PO4 gel for 15 seconds, washed with distilled water and air dried. A single coat of Adper Single Bond 2 adhesive was applied and photo polymerized for 20 seconds and Filtek Z-350 XT composite resin block of length 5 mm, width 4 mm and height 5 mm respectively was built and photo polymerized in increments for 20 seconds each. The shear bond strength of all the samples were measured (in MPa) on Instron Mechanical Testing Machine.
Results: The mean shear bond strength value for Group-A was 13.51 +/- 5.726 MPa and for Group-B being 15.06 +/- 6.220 MPa. No statistically significant difference in the shear bond strengths was observed between the two groups.
Conclusions: No significant effect of sodium hypochlorite enamel deproteinization on the shear bond strength of Adper Single Bond 2 adhesive and Filtek Z-350 XT composite resin before acid etching was observed in this study.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.17796/jcpd.36.1.l345875912750624 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
The effect of different adhesive strategies and diamond burs on dentin bond strength of universal resin cements.
Clin Oral Investig
January 2025
Department of Restorative Dentistry, Graduate School of Dental Medicine, Hokkaido University, Sapporo, Japan.
Objectives: To evaluate the shear bond strength (SBS) of universal cements (UCs) to dentin prepared with different diamond burs using various adhesive strategies.
Materials And Methods: One-hundred-twenty molars were prepared to expose the mid-coronal dentin. The teeth were divided into two groups according to diamond bur preparations: coarse and super-fine grit burs.
Debonding Characteristic and Survival Probability of Adhesive Flash-Free Ceramic Orthodontic Brackets Following pH Cycling.
Eur J Dent
December 2024
Department of Dental Biomaterials, Faculty of Dentistry, Mansoura University, Mansoura City, Egypt.
Objectives: Orthodontic bracket bond failure is an obstacle in clinical orthodontics. This study investigated the influence of pH cycling on the shear bond strength (SBS), adhesive remnant index (ARI), and survival probability of adhesive-precoated flash-free ceramic brackets.
Materials And Methods: Forty mandibular premolars were randomly divided into two groups ( = 20): C: noncoated orthodontic brackets, and F: flash-free adhesive-precoated orthodontic brackets.
Unravelling the Mechanical and Superconducting Properties in Borophene with Multicentered Bonds.
J Phys Chem Lett
January 2025
State Key Laboratory of Superhard Materials, Key Laboratory of Material Simulation Methods & Software of Ministry of Education, and Jilin Provincial International Cooperation Key Laboratory of High-Efficiency Clean Energy Materials, Jilin University, Changchun 130012, China.
The multicentered bonds present in planar borophene lead to a more complex structure and richer chemical properties. Herein, we use first-principles calculations to investigate the electronic, mechanical, and superconducting properties of various borophene polymorphs, focusing on the newly synthesized β and β phases. Notably, in order to balance and optimize the electron filling of the valence bond orbitals, the planar borophene structure is composed of a mixture of triangular lattices and hexagonal holes with multicentered bonding, which further enhances the stability of the structure and possesses a rare polymorphic property.
View Article and Find Full Text PDFEvaluation of the Mechanical and Biological Properties of Polycaprolactone Scaffolds Produced by a Material Extrusion 3D Printer or 3D Pen: A Novel Bone Repair Strategy.
J Biomed Mater Res B Appl Biomater
January 2025
Department and Research Institute of Dental Biomaterials and Bioengineering, Yonsei University College of Dentistry, Seoul, Republic of Korea.
Addressing the high cost and long cycle associated with the multistep digital restoration process involving 3D printing technology, we proposed the 3D pen as an innovative strategy for rapid bone repair. Capitalizing on the low melting point characteristic of polycaprolactone (PCL), we introduced, for the first time, the novel concept of directly constructing scaffolds at bone defect sites using 3D pens. In this in vitro study, we meticulously evaluated both the mechanical and biological properties of 3D pen-printed PCL scaffolds with six distinct textures: unidirectional (UNI) (0°, 45°, 90°), bidirectional (BID) (-45°/45°, 0°/90°), and concentric (CON).
View Article and Find Full Text PDFShear bond strength and ARI scores of metal brackets to glazed glass ceramics and zirconia: an in vitro study investigating surface treatment protocols.
BMC Oral Health
December 2024
Faculty of Dentistry, Innovative Dental Materials and Interfaces Research Unit (URB2i), UR 4462, Paris Cité University, 1 rue Maurice Arnoux, Montrouge, 92120, France.
Objective: To evaluate the shear bond strength (SBS) and adhesive remnant index (ARI) scores of metal brackets to glazed lithium disilicate reinforced glass-ceramics and zirconia according to various surface treatment protocols.
Methods: A total of 240 lithium disilicate ceramic (LD) and 240 zirconia (Zr) blocks were randomly divided according to sandblasting, hydrofluoric acid (HF) etching, universal primer use, and the adhesive system applied. A maxillary canine metal bracket was bonded to each sample with resin cement (Transbond XT, TXT).
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!