A novel material design was developed by functionalizing polyvinyl alcohol hydrogel with an organic low-friction boundary lubricant (molar ratios of 0.2, 0.5, and 1.0 moles of lauroyl chloride). The hydrogels were fabricated using two different techniques. First, the boundary lubricant was initially functionalized to the polymer, then the hydrogels were created by physically crosslinking the reacted polymer. Second, hydrogels were initially created by crosslinking pure polyvinyl alcohol, with the functionalization reaction performed on the fully formed gel. After the reaction, Fourier transform infrared spectroscopy and attenuated total reflectance spectra revealed a clear ester peak, the diminishment of the alcohol peak, and the amplification of the alkyl peaks, which confirmed attachment of the hydrocarbon chains to the polymer. Additional chemical characterization occurred through elemental analysis where an average increase of 22% carbon and 40% hydrogen provided further confirmation of attachment. Physical characterization of the boundary lubricant functionalized hydrogels was performed by water content and contact angle measurements. Water content dependency showed that method 1 had a direct relationship with boundary lubricant concentration, and method 2 displayed an inverse relationship. The contact angle increased as boundary lubricant concentration increased for the pure matrix material for both processing methods, suggesting that the hydrocarbons produced surface properties that mimic natural cartilage, and contact behavior of the biphasic system was dependent on processing method. Friction tests demonstrated a significant decrease in friction coefficient, with a maximum decrease of 70% and a minimum decrease of 24% for boundary lubricant functionalized hydrogels compared with nonfunctionalized polyvinyl alcohol hydrogels.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1002/jbm.b.32742 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Boundary Lubrication with Adsorbed Anionic Surfactant Bilayers in Hard Water.
Langmuir
January 2025
R&D - Analytical Science Research, Kao Corporation, 1334 minato, Wakayama, Wakayama 640-8580, Japan.
The adsorption behavior of an anionic surfactant, hydroxy alkane sulfonate with an alkyl chain length of 18 (C18HAS), from its hard water solution onto a mica surface and resulting lubrication properties were investigated. Because of the double chain-like chemical structure and aggregation behavior, C18HAS formed vesicles in hard water, which adsorbed onto a negatively charged mica surface via cation (Ca) bridging and then transformed into a bilayer film. The number of bilayers formed on the surface was evaluated by force curve measurements using an atomic force microscope (AFM), and the results showed a time-dependent increase of the number of adsorbed bilayers.
View Article and Find Full Text PDFComparison of Rheological and Tribological Properties of Cold Thickened Beverages for Dysphagia Management.
Prev Nutr Food Sci
December 2024
Department of Food Science and Biotechnology, Dongguk University-Seoul, Gyeonggi 10326, Korea.
This study investigated the rheological and tribological properties of cold beverages [bottled water (BW), sports drink (SD), orange juice (OJ), and whole milk (WM)] thickened with various concentrations (1%, 2%, and 3%, w/w) of xanthan gum-based food thickeners. All thickened beverages exhibited high pseudoplastic behavior, with increasing thickener concentration leading to higher viscosity and viscoelastic moduli and a lower flow behavior index. Thickened BW, SD, and WM exhibited typical Stribeck curves covering the boundary, mixed, and hydrodynamic lubrication regimes.
View Article and Find Full Text PDFDeployment of Industry 4.0 technologies to achieve a circular economy in agri-food supply chains: A thorough analysis of enablers.
J Environ Manage
January 2025
School of Economics and Management, Fuzhou University, Fuzhou, China. Electronic address:
With the global population projected to reach 9.7 billion by 2050, pressure on global natural resources will increase by 50-90%, exceeding planetary boundaries. Industry 4.
View Article and Find Full Text PDFImpact of oil-water emulsions on lubrication performance of ship stern bearings.
Sci Rep
December 2024
School of architecture, Ocean and energy power engineering, Wuhan University of Technology, Wuhan, 430070, China.
During maritime operations, extreme events such as explosions, grounding, and seal failures can cause water ingress into lubricant compartments, forming oil-water emulsions that significantly affect the lubrication performance of ship stern bearings. Existing studies mainly focus on low water content, with limited exploration of the impact of high water content on lubrication performance. To address this gap, viscosity measurements of oil-water mixtures were conducted, and an emulsification viscosity equation applicable to varying water contents was derived.
View Article and Find Full Text PDFMolecular dynamics study on the nanofriction and wear mechanism of transverse grain boundaries in nickel-based alloys.
J Mol Model
December 2024
School of Mechanical and Electrical Engineering, Lanzhou University of Technology, Lanzhou, 730050, China.
Context: This study employs molecular dynamics simulations to investigate the nanoscale tribological behavior of a single transverse grain boundary in a nickel-based polycrystalline alloy. A series of simulations were conducted using a repetitive rotational friction method to explore the mechanisms by which different grain boundary positions influence variations in wear depth, friction force, friction coefficient, dislocation, stress, and internal damage during repeated friction processes. The results reveal that the grain boundary structure enhances the strength of the nanoscale nickel-based polycrystalline alloy.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!