Mechanical behavior and interphase structure in a silica-polystyrene nanocomposite under uniaxial deformation.

Nanotechnology

Eduard-Zintl-Institut für Anorganische und Physikalische Chemie and Centre of Smart Interfaces, Technische Universität Darmstadt, Petersenstrasse 22, D-64287 Darmstadt, Germany.

Published: August 2012

The mechanical behavior of polystyrene and a silica-polystyrene nanocomposite under uniaxial elongation has been studied using a coarse-grained molecular dynamics technique. The Young's modulus, the Poisson ratio and the stress-strain curve of polystyrene have been computed for a range of temperatures, below and above the glass transition temperature. The predicted temperature dependence of the Young's modulus of polystyrene is compared to experimental data and predictions from atomistic simulations. The observed mechanical behavior of the nanocomposite is related to the local structure of the polymer matrix around the nanoparticles. Local segmental orientational and structural parameters of the deforming matrix have been calculated as a function of distance from nanoparticle's surface. A thorough analysis of these parameters reveals that the segments close to the silica nanoparticle's surface are stiffer than those in the bulk. The thickness of the nanoparticle-matrix interphase layer is estimated. The Young's modulus of the nanocomposite has been obtained for several nanoparticle volume fractions. The addition of nanoparticles results in an enhanced Young's modulus. A linear relation describes adequately the dependence of Young's modulus on the nanoparticle volume fraction.

Download full-text PDF

Source
http://dx.doi.org/10.1088/0957-4484/23/30/305702DOI Listing

Publication Analysis

Top Keywords

young's modulus
20
mechanical behavior
12
silica-polystyrene nanocomposite
8
nanocomposite uniaxial
8
dependence young's
8
nanoparticle's surface
8
nanoparticle volume
8
young's
5
modulus
5
behavior interphase
4

Similar Publications

3D printed Aloe barbadensis loaded alginate-gelatin hydrogel for wound healing and scar reduction: In vitro and in vivo study.

Int J Biol Macromol

January 2025

Department of Stem Cell and Regenerative Medicine and Medical Biotechnology, Centre for Interdisciplinary Research, D. Y. Patil Education Society (Deemed to be University), Kolhapur 416006, MS, India. Electronic address:

Wounds are one of the most critical clinical issues in plastic surgery repair and restoration. Conventional wound dressing materials cannot absorb enough wound exudates and shield the site from microbial infection. Also, despite their healing prowess, bioactive molecules from medicinal plants are less bioavailable at the wound sites.

View Article and Find Full Text PDF

Cartilaginous microtissues exhibit extreme resilience under compression with size-dependent mechanical properties.

Biomaterials

January 2025

Prometheus Division of Skeletal Tissue Engineering, KU Leuven, O&N1, Herestraat 49, PB 813, 3000, Leuven, Belgium; Skeletal Biology and Engineering Research, KU Leuven, ON1 Herestraat 49, PB 813, 3000, Leuven, Belgium. Electronic address:

Self-assembled cartilaginous microtissues provide a promising means of repairing challenging skeletal defects and connective tissues. However, despite their considerable promise in tissue engineering, the mechanical response of these engineered microtissues is not well understood. Here we examine the mechanical and viscoelastic response of progenitor cell aggregates formed from human primary periosteal cells and the resulting cartilaginous microtissues under large deformations as might be encountered in vivo.

View Article and Find Full Text PDF

Atomic Force Microscopy (AFM) nanoindentation is the most effective method for determining the mechanical properties of soft biological materials and biomaterials at the nanoscale, with significant applications in many areas, including cancer diagnosis. However, a major drawback of this method is the complexity of the experimental procedure and data processing, which requires several calibration steps.To avoid this complexity, the AFM tip is usually approximated as a perfect cone.

View Article and Find Full Text PDF

The surface characteristics of scaffolds utilized in bone tissue engineering profoundly influence subsequent cellular response. This study investigated the efficacy of applying a gelatin coat to the surface of aminolysis surface-modified scaffolds fabricated through 3D printing with a polycaprolactone/hydroxyapatite nanocomposite, employing the hot-melt extrusion FDM technique. Initially, aminolysis surface modification using hexamethylenediamine enhanced surface hydrophilicity by introducing amine functional groups.

View Article and Find Full Text PDF

Triply periodic minimal surface (TPMS) metamaterials show promise for thermal management systems but are challenging to integrate into existing packaging with strict mechanical requirements. Composite TPMS lattices may offer more control over thermal and mechanical properties through material and geometric tuning. Here, we fabricate copper-plated, 3D-printed triply periodic minimal surface primitive lattices and evaluate their suitability for battery thermal management systems.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!