During the 1960s, the midge, Eretmoptera murphyi, was transferred from sub-Antarctic South Georgia (55°S 37°W) where it is endemic to a single location on maritime Antarctic Signy Island (60°S 45°W). Its distribution has since expanded considerably, suggesting that it is pre-adapted to the more severe conditions further south. To test one aspect of the level of its pre-adaptation, the rapid cold hardening (RCH) response in this species was investigated. When juvenile (L1-L2) and mature (L3-L4) larvae of E. murphyi were directly exposed to progressively lower temperatures for 8h, they exhibited Discriminating Temperatures (DTemp, temperature at which there is 10-20% survival of exposed individuals) of -11.5 and -12.5°C, respectively. The mean SCP was above -7.5°C in both larval groups, confirming the finding of previous studies that this species is freeze-tolerant. Following gradual cooling (0.2°Cmin(-1)), survival was significantly greater at the DTemp in both larval groups. The response was strong, lowering the lower lethal temperature (LLT) by up to 6.5°C and maintaining survival above 80% for at least 22h at the DTemp. RCH was also exhibited during the cooling phase of an ecologically relevant thermoperiodic cycle (+4°C to -3°C). Mechanistically, the response did not affect freezing, with no alteration in the supercooling point (SCP) found following gradual cooling, and was not induced while the organism was in a frozen state. These results are discussed in light of E. murphyi's pre-adaptation to conditions on Signy Island and its potential to colonize regions further south in the maritime Antarctic.

Download full-text PDF

Source
http://dx.doi.org/10.1016/j.jinsphys.2012.05.009DOI Listing

Publication Analysis

Top Keywords

cold hardening
8
midge eretmoptera
8
eretmoptera murphyi
8
maritime antarctic
8
signy island
8
larval groups
8
gradual cooling
8
pre-adapted maritime
4
maritime antarctic?--rapid
4
antarctic?--rapid cold
4

Similar Publications

In this study, we investigated the effect of spray angle on the microstructure, bonding quality, and scratch resistance of cold-sprayed SS316L coatings on SS304 substrates. The coatings were deposited at spray angles of 45°, 60°, 75°, and 90° using a high-pressure cold spray system. A comprehensive analysis of the relationship between the spray angle and coating properties was conducted, with a particular focus on fracture toughness and porosity.

View Article and Find Full Text PDF

High-performance lightweight materials are urgently needed because of energy savings and emission reduction. Here, we design a new steel with a low density of 6.41 g/cm, which is a 20% weight reduction compared to the conventional steel.

View Article and Find Full Text PDF

The adaptation of 3D printing techniques within the construction industry has opened new possibilities for designing and constructing cementitious materials efficiently and flexibly. The layered nature of extrusion-based concrete printing introduces challenges, such as interlayer weaknesses, that compromise structural integrity and mechanical performance. This experimental study investigates the influence of interlayer orientation and the presence of cold joints (CJ) on mechanical properties, such as stiffness and strength.

View Article and Find Full Text PDF

Face-centered cubic (FCC)-structured high-entropy alloys (HEAs) are facing a major challenge due to a trade-off between strength and ductility. In this paper, we systematically investigated the microstructural evolution and tensile properties of metastable dual-phase (DP) FeMnCoCr HEAs via cold rolling and partial recrystallized annealing, which resulted in a heterogeneous microstructure, and by inducing strengthening and strain-hardening through heterogeneous deformation-induced (HDI) strategies. The results show that the alloy was annealed at 600 °C for 10 min, exhibiting a good combination of strength and ductility.

View Article and Find Full Text PDF

This study selected 17-4PH (Type 630) precipitation-hardening stainless steel as the raw material. After subjecting the material to precipitation hardening and softening heat treatments, the effects of these treatments on the microstructural characteristics and mechanical properties were investigated, along with a thermal fatigue test. The results showed that after the precipitation hardening heat treatment, the ultimate tensile strength and hardness of 17-4PH stainless steel increased.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!