Electrospun polycaprolactone nanofiber matrices surface functionalized with poly[(ethyl alanato), (p-methyl phenoxy),] phosphazene were fabricated for the purpose of soft skeletal tissue regeneration. This preliminary study reports the effect of fiber diameter and polyphosphazene surface functionalization on significant scaffold properties such as morphology, surface hydrophilicity, porosity, tensile properties, human mesenchymal stem cell adhesion and proliferation. Six fiber matrices comprised of average fiber diameters in the range of 400-500, 900-1000, 1400-1500, 1900-2000, 2900-3000 and 3900-4000 nm were considered for primary evaluation. After achieving the greatest proliferation while maintaining moderate tensile modulus, matrices in the diameter range of 2900-3000 nm were selected to examine the effect of coating with 1%, 2% and 3% (weight/volume) polyphosphazene solutions. Polyphosphazene functionalization resulted in rougher surfaces that correlated with coating solution concentration. Analytical techniques such as energy dispersive X-ray analysis, Fourier transform infrared spectroscopy, elemental analysis, differential scanning calorimetry, water contact angle goniometry and confocal microscopy confirmed the presence of polyphosphazene and its distribution on the functionalized fiber matrices. Functionalization achieved through 2% polymer solutions did not affect average pore diameter, tensile modulus, suture retention strength or cell proliferation compared to PCL controls. Surface polyphosphazene functionalization significantly improved the matrix hydrophilicity evidenced through decreased water contact angle of PCL matrices from 130 degrees to 97 degrees. Further, enhanced total protein synthesis by cells during in vitro culture was seen on 2% PPHOS functionalized matrices over controls. Improving PCL matrix hydrophilicity via proposed surface functionalization may be an efficient method to improve cell-PCL matrix interactions.

Download full-text PDF

Source
http://dx.doi.org/10.1166/jbn.2012.1368DOI Listing

Publication Analysis

Top Keywords

fiber matrices
12
functionalized fiber
8
tissue regeneration
8
surface functionalization
8
tensile modulus
8
polyphosphazene functionalization
8
water contact
8
contact angle
8
matrix hydrophilicity
8
matrices
7

Similar Publications

Efficient luminescent solar concentrators based on solvent polarity induced multiple-colored carbon dots.

J Colloid Interface Sci

January 2025

State Key Laboratory of Bio-Fibers and Eco-Textiles, Qingdao University, No. 308 Ningxia Road, Qingdao 266071 PR China. Electronic address:

Luminescent solar concentrators (LSCs) are large scale sunlight collector and can be used for building-integrated photovoltaics (BIPV). Achieving high-performance LSCs requires fluorophores with broad absorption, high quantum yield and a large Stokes shift. Nevertheless, conventional high-efficiency LSCs typically rely on heavy metal-based quantum dots as fluorophores.

View Article and Find Full Text PDF

In this work, the fracture mechanism of winding carbon-fiber-reinforced plastics (CFRPs) based on epoxy matrices reinforced by polysulfone film was investigated. Two types of polymer matrices were used: epoxy oligomer (EO) cured by iso-methyltetrahydrophthalic anhydride (iso-MTHPA), and EO-modified polysulfone (PSU) with active diluent furfuryl glycidyl ether (FGE) cured by iso-MTHPA. At the winding stage, the reinforcing film was placed in the middle layer of the CFRP.

View Article and Find Full Text PDF

Recycling end-of-life wind turbines poses a significant challenge due to the increasing number of turbines going out of use. After many years of operation, turbines lose their functional properties, generating a substantial amount of composite waste that requires efficient and environmentally friendly processing methods. Wind turbine blades, in particular, are a problematic component in the recycling process due to their complex material composition.

View Article and Find Full Text PDF

Comparison of the Performance of Nonlinear Time-Dependent Constitutive Models Calibrated with Minimal Test Data Applied to an Epoxy Resin.

Materials (Basel)

January 2025

CITAB-Centre for the Research and Technology of Agro-Environmental and Biological Sciences, School of Science and Technology, University of Trás-os-Montes and Alto Douro, 5000-801 Vila Real, Portugal.

Epoxy resins are extensively employed as adhesives and matrices in fibre-reinforced composites. As polymers, they possess a viscoelastic nature and are prone to creep and stress relaxation even at room temperature. This phenomenon is also responsible for time-dependent failure or creep fracture due to cumulative strain.

View Article and Find Full Text PDF

Carbon-fiber-reinforced polymers (CFRPs) with epoxy matrices are widely applied in high-performance structural applications and represent one of the biggest classes of materials with urgent need for end-of-life management. Available waste management methodologies for conventional thermoset composites with a focus on CFRPs are briefly reviewed and their limitations are highlighted. In the quest to obtain materials with mechanical performance, thermal stability, and sustainability, the research community has turned its interest to develop polymer composites with adaptable and dynamic networks in their matrix, and lately also at an interface/interphase level.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!