AI Article Synopsis

  • The study assessed cetyl trimethyl ammonium bromide (CTAB) as a new method for isolating beneficial entomopathogenic fungi compared to the existing method using dodine.
  • Oatmeal agar with chloramphenicol was utilized, testing three concentrations of CTAB, with 0.6 g/L proving most effective for promoting growth in targeted fungi while preventing non-target species from sporulating.
  • Results indicate that OA + 0.6 g/L CTAB is a cost-effective, efficient alternative for isolating specific fungi like Beauveria bassiana, Metarhizium anisopliae, and Paecilomyces lilacinus from soil samples.

Article Abstract

This study evaluated the quaternary ammonium compound cetyl trimethyl ammonium bromide (CTAB) as an alternative to the chemically related dodecylguanidine (dodine) for the selective isolation of entomopathogenic fungi. Oatmeal agar (OA) with chloramphenicol was used as basal medium, and three concentrations of CTAB (0.5, 0.6, 0.7 g/L) were evaluated and compared against OA + 0.46 g/L dodine. Selective isolation and growth studies were performed with the entomopathogens Beauveria bassiana, Metarhizium anisopliae s.l. and Paecilomyces lilacinus and five common non-entomopathogenic non-target species. The three entomopathogenic fungi sporulated earlier on OA + 0.6 g/L CTAB than on OA + 0.46 g/L dodine, while none of the non-target fungi sporulated on OA + 0.6 g/L CTAB. All entomopathogenic fungal isolates grew on OA + 0.6 g/L CTAB, despite some intra-species variation, whereas non-target fungi showed no growth or sporulation. OA + 0.6 g/L CTAB resulted in an efficient medium to isolate B. bassiana, M. anisopliae s. l. and P. lilacinus from soil samples. Results of our study suggest that OA + 0.6 g/L CTAB is a suitable, simple and inexpensive to prepare medium to replace OA + 0.46 g/L dodine for the selective isolation of these fungi.

Download full-text PDF

Source
http://dx.doi.org/10.3852/11-234DOI Listing

Publication Analysis

Top Keywords

g/l ctab
20
dodine selective
12
selective isolation
12
046 g/l
12
g/l dodine
12
g/l
9
cetyl trimethyl
8
trimethyl ammonium
8
ammonium bromide
8
ctab
8

Similar Publications

PTFE layer formation during brush electroplating of nickel.

Sci Rep

October 2024

Universidad Loyola Andalucía, 41704, Dos Hermanas, Seville, Spain.

Brush electrodeposition of Ni/PTFE composite coatings was explored using a nickel high speed solution and polytetrafluoroethylene (PTFE) particles 6-9 μm in diameter. A novel bilayer-like, partially intercalated structure was produced, consisting of a rough nickel sublayer covered by an outer, compact, smooth PTFE layer. The study of the coating growth revealed that the PTFE particles bind together on the nickel coating valleys and grow until all the surface is covered by a polymer layer without the need of a baking stage.

View Article and Find Full Text PDF

Hyaluronic acid production by Streptococcus zooepidemicus MW26985 using potato peel waste hydrolyzate.

Bioprocess Biosyst Eng

July 2024

Biotechnology Research Laboratory, Department of Biochemical Engineering, Faculty of Chemical Engineering, Babol Noshirvani University of Technology, P.O. Box 47148-71167, Babol, Iran.

In this research, we examined the production of hyaluronic acid (HA) by Streptococcus zooepidemicus strain MW26985 using different substrates and potato peel waste (PPW) as an affordable substrate. First, culture medium components, including carbon and nitrogen sources, were optimized for bacterial HA production. Five different carbon sources (glucose, sucrose, lactose, sago starch, and potato starch, at a concentration of 30 g/L) and three distinct nitrogen sources (peptone, yeast extract, and ammonium sulfate, at a concentration of 10 g/L) were investigated.

View Article and Find Full Text PDF

Background: High-quality RNA extraction from woody plants is difficult because of the presence of polysaccharides and polyphenolics that bind or co-precipitate with the RNA. The CTAB (cetyl trimethylammonium bromide) based method is widely used for the isolation of nucleic acids from polysaccharide-rich plants. Despite the widespread use of the CTAB method, it is necessary to adapt it to particular plant species, tissues and organs.

View Article and Find Full Text PDF

Green application of surfactant modified silica as effective sorbent for extraction and preconcentration of sulfonamide residues in environmental water and honey samples.

J Chromatogr A

March 2024

Creative Chemistry and Innovation Research Unit, Department of Chemistry and Center of Excellence for Innovation in Chemistry, Faculty of Science, Mahasarakham University, Maha Sarakham 44150, Thailand; Multidisciplinary Research Unit of Pure and Applied Chemistry (MRUPAC), Department of Chemistry and Center of Excellent for Innovation in Chemistry, Faculty of Science, Mahasarakham University, Maha Sarakham 44150, Thailand. Electronic address:

Micro-solid phase extraction (µ-SPE) using surfactant coated silica for extraction and preconcentration of sulfonamide residues at trace levels in environmental water and honey samples prior their analysis by high performance liquid chronatography coupled with photodiode array detector (HPLC-PDA). The sample solution were dispersed in a small amounts of solid sorbent by vacuum manifold for sample preparation, and extraction occurred by adsorption in a short time. Finally, the analytes were subsequently desorbed using an appropriate solvent.

View Article and Find Full Text PDF

Surface Defect Mitigation of Additively Manufactured Parts Using Surfactant-Mediated Electroless Nickel Coatings.

Materials (Basel)

January 2024

The Functional Materials and Chemistry Group, Centre for Manufacturing and Materials, The Institute for Advanced Manufacturing and Engineering, Coventry University, Beresford Ave., Coventry CV6 5LZ, UK.

The emergence of defects during the early production phases of ferrous-alloy additively manufactured (AM) parts poses a serious threat to their versatility and adversely impacts their overall mechanical performance in industries ranging from aerospace engineering to medicine. Lack of fusion and gas entrapment during the manufacturing stages leads to increased surface roughness and porosities in the finished part. In this study, the efficacy of employing electroless nickel-boron (Ni-B) deposition to fill and level simulated AM defects was evaluated.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!