Purpose: The purpose of this study was to evaluate the rotational freedom between implant and abutment counterpart of two abutments types over external hexagon implants submitted to mechanical cycling.
Materials And Methods: Ten implants with external hexagon (3.75 mm × 13 mm), five cast abutments, and five premachined abutments both with 4.1 mm plataform size were used in this study. Ten metallic crowns were fabricated using the two types of abutments and were fixed to each implant using titanium screws (Ti6Al4V). Rotational freedom measurements were made before and after the cast procedure and after the mechanical cycling. Groups were classified according to the rotational misfit register using University of California, Los Angeles abutment and implants as new (group 1 = G1); using crowns and implants after crown casting (group 2 = G2); and using crowns and implants after mechanical cycling (group 3 = G3). Oblique loading of 120N at 1.8 Hz and 5 × 10(5) cycles was applied on specimen.
Results: Statistical analysis (p < .05) showed that no significant difference was observed when cast abutment was compared with premachined abutment after casting (p = .390) and mechanical cycling (p = .439); however, significant difference was noted before the casting (p = .005) with higher values for the cast abutments.
Conclusions: Within the limitations of this in vitro study, it could be concluded that the abutment type used do not influenced the rotational freedom after casting and the amount of applied cycles (500,000 cycles) was not sufficient to significantly alter the values of rotational freedom at the implant/abutment joint.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/j.1708-8208.2011.00430.x | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Stacking-Engineered Ferroelectricity and Multiferroic Order in van der Waals Magnets.
Phys Rev Lett
December 2024
John A. Paulson School of Engineering and Applied Sciences, Harvard University, Cambridge, Massachusetts 02138, USA.
Two-dimensional (2D) materials that exhibit spontaneous magnetization, polarization, or strain (referred to as ferroics) have the potential to revolutionize nanotechnology by enhancing the multifunctionality of nanoscale devices. However, multiferroic order is difficult to achieve, requiring complicated coupling between electron and spin degrees of freedom. We propose a universal method to engineer multiferroics from van der Waals magnets by taking advantage of the fact that changing the stacking between 2D layers can break inversion symmetry, resulting in ferroelectricity as well as magnetoelectric coupling.
View Article and Find Full Text PDFMetrology with a twist: probing and sensing with vortex light.
Light Sci Appl
January 2025
School of Physics, University of the Witwatersrand, Private Bag 3, Johannesburg, 2050, South Africa.
Optical metrology is a well-established subject, dating back to early interferometry techniques utilizing light's linear momentum through fringes. In recent years, significant interest has arisen in using vortex light with orbital angular momentum (OAM), where the phase twists around a singular vortex in space or time. This has expanded metrology's boundaries to encompass highly sensitive chiral interactions between light and matter, three-dimensional motion detection via linear and rotational Doppler effects, and modal approaches surpassing the resolution limit for improved profiling and quantification.
View Article and Find Full Text PDFA flat posterior cruciate ligament reconstruction restores native knee kinematics, comparable to a double-bundle reconstruction-A biomechanical robotic investigation.
Knee Surg Sports Traumatol Arthrosc
December 2024
Department of Trauma, Hand and Reconstructive Surgery, University Hospital Münster, Münster, Germany.
Purpose: To biomechanically evaluate a flat posterior cruciate ligament (PCL) reconstruction utilizing rectangular femoral bone tunnels.
Methods: Eight fresh-frozen human knee specimens were tested in a six-degrees-of-freedom robotic test setup. In each testing step, a force-controlled test protocol was performed, including 89 N posterior tibial translation (PTT) in neutral, internal and external rotation, from 0 to 90° of flexion.
A dynamic knee function scoring system for anterior cruciate ligament injuries based on normative six-degree-of-freedom gait pattern.
BMC Musculoskelet Disord
December 2024
Sports Medicine Center, West China Hospital, Sichuan University, Chengdu, China.
Background: Traditional examinations of anterior cruciate ligament (ACL) injuries focus primarily on static assessments and lack the ability to evaluate dynamic knee stability. Hence, a dynamic scoring system for knee function is needed in clinical settings. This study aimed to propose a dynamic scoring system based on a large sample of normative six-degree-of-freedom (6-DOF) knee kinematics during gait, and validate its correlation with conventional outcome measurements in assessing ACL-injured knees.
View Article and Find Full Text PDFAnalysis of shoulder motion with inertial sensors in Poland syndrome patients.
Musculoskelet Surg
December 2024
Plastic and Reconstructive Surgery Department, IRCCS Ospedale Policlinico San Martino, Genoa, Italy.
Purpose: Poland syndrome is a congenital malformation characterized by agenesis or hypoplasia of pectoralis muscles. There is a limited literature on how the anatomic anomalies of PS may impact the movement of the shoulder. This study analyzes the effects of absence of the pectoralis muscles on the shoulder kinematic.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!