Objectives: The purpose of this study was to evaluate the flexural strength and Vickers hardness of a microwave energy heat-cured acrylic resin by adding different concentrations of silane surface-treated nanoparticle silica.
Methods: Acrylic resin specimens with dimensions of 65 × 10 × 2.5 mm were formed and divided into five experimental groups (n = 10) according to the silica concentration added to the acrylic resin mass (weight %) prior to polymerisation : G1, without silica; G2, 0.1% silica; G3, 0.5% silica; G4, 1.0% silica; and G5, 5.0% silica. The specimens were submitted to a three-point flexural strength test and to the Vickers hardness test (HVN). The data obtained were statistically analysed by anova and the Tukey test (α = 0.05).
Results: Regarding flexural strength, G5 differed from the other experimental groups (G1, G2, G3 and G4) presenting the lowest mean, while G4 presented a significantly higher mean, with the exception of group G3. Regarding Vickers hardness, a decrease in values was observed, in which G1 presented the highest hardness compared with the other experimental groups.
Conclusion: Incorporating surface-treated silica resulted in direct benefits in the flexural strength of the acrylic resin activated by microwave energy; however, similar results were not achieved for hardness.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/j.1741-2358.2011.00604.x | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
A technique to enhance the gingival esthetics of a prototype complete arch fixed implant-supported prototype prosthesis using a 3D printed gingival veneer.
J Prosthet Dent
December 2024
Clinical Professor and Program Director, University of Connecticut Health Center, Farmington, Conn.; and Private practice, Glastonbury, Conn. Electronic address:
An important step in the workflow for a complete arch fixed implant-supported prosthesis is the fabrication of a prototype resin prosthesis to allow the patient to visualize the definitive treatment outcome and also to use as an interim prosthesis. Producing a prototype prosthesis with the natural appearance of the gingival color and contour has been challenging. Current methods include painted stains, manually applied pink composite resin or autopolymerizing acrylic resin, and multicolored resin blocks, but these are all relatively expensive, have less than optimal esthetics, and are labor-intensive and time-consuming.
View Article and Find Full Text PDFComparative Assessment of Push-Out Bond Strength and Dentinal Tubule Penetration of Different Calcium-Silicate-Based Endodontic Sealers.
Dent J (Basel)
December 2024
Faculty of Dentistry, Iuliu Hatieganu University of Medicine and Pharmacy, 400012 Cluj-Napoca, Romania.
Adhesion within endodontic obturation material and root canal walls improves the efficacy of the endodontic treatment by establishing a barrier that inhibits reinfection and entombs residual bacteria. This study evaluates the push-out bond strength (POBS) of calcium silicate sealers compared to an epoxy-resin-based sealer. A total of 36 extracted mono-radicular teeth were prepared with Pro Taper Ultimate and irrigated with 5.
View Article and Find Full Text PDFEvaluation of Shear Bond Strength of Lithium Disilicate Veneers Using Pre-heated Resin Composite With Two Conventional Resin Cements: An In Vitro Study.
Cureus
November 2024
Department of Endodontic and Operative Dentistry, Damascus University, Damascus, SYR.
Objectives This study aimed to compare the shear bond strength of three resin cements (light-cured resin cement, pre-heated composite resin, and dual-cured self-adhesive resin cement) when bonding to lithium disilicate discs. Materials and methods Thirty-six discs made of lithium disilicate were fabricated and etched with 9.5% (HF), and 36 human premolars were collected and immersed in the acrylic molds, then randomly divided into three equal groups (n = 12): Group 1: light-cured resin cement, Group 2: pre-heated resin composite, and Group 3: dual-cured resin cement.
View Article and Find Full Text PDFAn In Vitro Study to Assess the Effect of Cigarette Smoke on Color Stability and Surface Roughness of 3D Printed, Milled, and Traditional Provisional Crown and Bridge Materials.
Cureus
November 2024
General Dentistry and Comprehensive Care, NYU College of Dentistry, New York University, New York, USA.
Objectives To assess the influence of cigarette smoke (CS) on the color and surface roughness of 3D printed, milled, and traditionally fabricated provisional crown and bridge (PC&B) materials. Materials and methods 112 disc-shaped samples were made employing four techniques and materials (28 per group) to fabricate PC&B prostheses. Specimens were fabricated using standard protocols, such as 3D printing, milling, conventional bis-acrylic resin, and traditional autopolymerizing polymethyl methacrylate (PMMA) resin.
View Article and Find Full Text PDFA Case Report Describing the Surgical Removal of Venous and Intracardiac Cement Leakage after Percutaneous Vertebroplasty in a Hybrid Operating Room.
Ann Ital Chir
December 2024
Department of Cardiovascular Surgery, Centro Cardiologico Monzino IRCCS, 20138 Milan, Italy; Department of Biomedical, Surgical, and Dental Sciences, University of Milan, 20122 Milan, Italy.
Aim: Percutaneous vertebroplasty is generally considered a safe procedure, however, cases of cardioembolism and cardiac perforation have been reported.
Case Presentation: A 69-year-old woman was referred to our emergency department after an outpatient echocardiogram revealed a "thrombus-like" formation involving the right heart. Two weeks before she had undergone percutaneous vertebroplasty of the third to fifth lumbar vertebrae due to osteoporotic fractures.
Want AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!