An array of parallel planar nanochannels containing two or three segments with varying inner heights was fabricated and used for size fractionation of inorganic and biological nanoparticles. A liquid suspension of the particles was simply drawn through the nanochannels via capillary action. Using fluorescently labeled 30 nm polyacrylonitrile beads, different trapping behaviors were compared using nanochannels with 200-45 nm and 208-54-30 nm height segments. Addition of sodium dodecyl sulfate (SDS) surfactant to the liquid suspension and application of an AC electric field were shown to aid in the prevention of channel clogging. After initial particle trapping at the segment interfaces, significant particle redistribution occurred when applying a sinusoidal 8V peak-to-peak oscillating voltage with a frequency of 150 Hz and DC offset of 4V. Using the 208-54-30 nm channels, 30 nm hepatitis B virus (HBV) capsids were divided into three fractions. When the AC electric field was applied to this trapped sample, all of the virus particles passed through the interfaces and accumulated at the channel ends.
Download full-text PDF |
Source |
---|---|
http://dx.doi.org/10.1016/j.chroma.2011.10.005 | DOI Listing |
Langmuir
January 2025
Brigham Young University, Provo, Utah 84602, United States.
Accurate models for predicting drop dynamics, such as maximum drop departure sizes, are crucial for estimating heat transfer rates during condensation on superhydrophobic (SH) surfaces. Previous studies have focused on examining the heat transfer rates for SH surfaces under the influence of gravity or vapor flowing over the surface. This study investigates the impact of surface solid fraction and texture scale on drop mobility in a condensing environment with a humid air flow.
View Article and Find Full Text PDFToxics
January 2025
Beijing Key Laboratory of Resource-Oriented Treatment of Industrial Pollutants, School of Energy and Environmental Engineering, University of Science and Technology Beijing, Beijing 100083, China.
Road dust carries various contaminants and causes urban non-point source pollution in waterbodies through runoff. Road dust samples were collected in each month in two years and then sieved into five particle size fractions. The concentrations of ten heavy metals (As, Cd, Cr, Cu, Hg, Mn, Ni, Pb, Zn, Fe) in each fraction were measured.
View Article and Find Full Text PDFNanomaterials (Basel)
January 2025
Faculty of Engineering, University of Kragujevac, SestreJanjić 6, 34000 Kragujevac, Serbia.
Magnesium-based materials, which are known for their light weight and exceptional strength-to-weight ratio, hold immense promise in the biomedical, automotive, aerospace, and military sectors. However, their inherent limitations, including low wear resistance and poor mechanical properties, have driven the development of magnesium-based metal matrix composites (Mg-MMCs). The pivotal role of powder metallurgy (PM) in fabricating Mg-MMCs was explored, enhancing their mechanical and corrosion resistance characteristics.
View Article and Find Full Text PDFMar Drugs
January 2025
Section of Food and Nutrition, School of Agriculture and Food Science, University College Dublin, Belfield, D04 V1W8 Dublin, Ireland.
A rise in antimicrobial resistance coupled with consumer preferences towards natural preservatives has resulted in increased research towards investigating antimicrobial compounds from natural sources such as macroalgae (seaweeds), which contain antioxidant, antimicrobial, and anticancer compounds. This study investigates the antimicrobial activity of compounds produced by the Irish seaweed against and , bacterial species which are relevant for food safety. Microwave-assisted extraction (MAE), ultrasound-assisted extraction (UAE), ultrasound-microwave-assisted extraction (UMAE), and conventional extraction technologies (maceration) were applied to generate extracts from , followed by their preliminary chemical composition (total phenolic content, total protein content, total soluble sugars) and antimicrobial activity (with minimum inhibitory concentration determined by broth microdilution methods), examining also the molecular weight distribution (via high performance size exclusion chromatography) and oligosaccharide fraction composition (via high-performance liquid chromatography) of the polysaccharides, as they were the predominant compounds in these extracts, aiming to elucidate structure-function relationships.
View Article and Find Full Text PDFEntropy (Basel)
December 2024
AGH University of Krakow, Faculty of Metals Engineering and Industrial Computer Science, al. Mickiewicza 30, 30-059 Kraków, Poland.
Functionally graded materials (FGMs) show continuous variations in properties and offer unique multifunctional capabilities. This study presents a simulation of the powder bed fusion (PBF) process for FGM fabrication using a combination of Unity-based deposition and lattice Boltzmann method (LBM)-based process models. The study introduces a diffusion model that allows for the simulation of material mixtures, in particular AISI 316L austenitic steel and 18Ni maraging 300 martensitic steel.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!