Zooplankton in the ocean respond to visual and hydro-mechanical cues such as small-scale shear in turbulent flow. In addition, they form strong aggregations where currents intersect sloping bottoms. Strong and predictable tidal currents over a sill in Knight Inlet, Canada, make it an ideal location to investigate biological behaviour in turbulent cross-isobath flow. We examine acoustic data (38, 120 and 200 kHz) collected there during the daylight hours, when the dominant zooplankters, Euphausia pacifica have descended into low light levels at ∼90 m. As expected, these data reveal strong aggregations at the sill. However, they occur consistently 10-20 m below the preferred light depth of the animals. We have constructed a simple model of the flow to investigate this phenomenon. Tracks of individual animals are traced in the flow and a variety of zooplankton behaviours tested. Our results indicate that the euphausiids must actively swim downward when they encounter the bottom boundary layer (bbl) to reproduce the observed downward shift in aggregation patterns. We suggest that this behaviour is cued by the small-scale shear in the bbl. Furthermore, this behaviour is likely to enhance aggregations found in strong flows at sills and on continental shelves.
Download full-text PDF |
Source |
---|---|
http://www.ncbi.nlm.nih.gov/pmc/articles/PMC3181040 | PMC |
http://dx.doi.org/10.1093/plankt/fbr074 | DOI Listing |
Phys Rev Lett
November 2024
Chemical and Biological Physics Department, Weizmann Institute of Science, Rehovot 7610001, Israel.
Cracks develop various surface patterns as they propagate in three-dimensional (3D) materials. Symmetry-breaking topological defects in nominally tensile (mode-I) fracture emerge in the slow (noninertial) regime, taking the form of surface steps. We show that the same phase-field framework that recently shed basic light on dynamic (inertial) tensile fracture in three dimensions, also gives rise to crack surface steps.
View Article and Find Full Text PDFJ Acoust Soc Am
December 2024
Department of Biomedical Engineering, Duke University, Durham, North Carolina 27708, USA.
The stress-strain relation in a transversely isotropic (TI) material is described by five independent parameters. In the incompressible limit, only three parameters are required to describe shear wave propagation. Existing material parameterization models are not ideal for the analysis of wave propagation in the nearly incompressible TI (NITI) regime due to difficult-to-interpret parameters, complicated forms of the stiffness matrix elements, or the lack of five independent parameters.
View Article and Find Full Text PDFSci Rep
December 2024
Department of electrical engineering, college of engineering, King Saud University, Riyadh, 11421, Saudi Arabia.
Plain flaps (PFs) significantly increase camber, enhancing lift and aerodynamic performance when deployed. In Darrieus Vertical Axis Wind Turbines (VAWTs), which perform efficiently in low-speed, turbulent wind conditions, structural modifications like PFs can improve efficiency. This study explores plain flaps with 10-20-degree deflections at different chord lengths to enhance the NACA 2412 aerofoil's performance.
View Article and Find Full Text PDFBiotechnol Bioeng
November 2024
AVT - Biochemical Engineering, RWTH Aachen University, Aachen, North Rhine-Westphalia, Germany.
Culture broth with secreted macromolecules and culture broth of filamentous fungi showing disperse growth exhibit elevated viscosity, usually with shear-thinning flow behavior. High viscosity, however, poses a serious challenge in the production and research of these compounds and organisms. It commonly causes insufficient mixing and oxygen transfer in large- and small-scale bioreactors.
View Article and Find Full Text PDFJ Mech Behav Biomed Mater
January 2025
School of Electrical and Mechanical Engineering, The University of Adelaide, Adelaide, SA, 5005, Australia. Electronic address:
While titanium alloy (Ti-6Al-4V) made by laser powder bed fusion (L-PBF) exhibits complex deformation behaviors, its important micromechanical properties in relation to loading directions are not fully understood. This research aims to investigate the micromechanical behaviors of printed L-PBF Ti-6Al-4V alloys under vertical (i.e.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!