CdTe nanoparticle-polymer composite films were deposited conformally using a layer-by-layer (LbL) process onto planar or ZnO nanorod-coated substrates. Films were annealed between 150-450 degrees C. Under air this led to oxidation of the nanoparticles while under vacuum their composition was retained. Annealing at 450 degrees C led to complete removal of the polymer with a loss of quantum confinement as shown by UV-vis spectroscopy. Annealing at 350 degrees C gave partial removal of the polymer and retained quantum confinement. Such annealed nanoparticle composite systems may have application in photovoltaics.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1166/jnn.2011.4154 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
2D Titanium Carbide MXene-Interfaced Zinc Oxide/Tungstite Architectures Adorned Mixed Matrix Polymer Membranes for Oily Wastewater Treatment.
ACS Appl Mater Interfaces
January 2025
Department of Physics, National Institute of Technology Nagaland, Chumukedima, Dimapur 797103, India.
An exceedingly porous and interwoven fibrous structure was achieved in this study by interlocking titanium carbide (TiC) MXenes onto the electrospun mats using poly(vinylidene fluoride) (PVDF) as the base polymer. The fibrous membrane was further modified with the inclusion of zinc oxide (ZnO) and tungstite (WO·HO) nano/microstructures via annealing and hydrothermal approaches. Through these strategic interfaced morphological developments in novel TiC/ZnO/WO·HO heterostructures, our findings reveal enhanced wettability and charge-segregation desirable for promoting oil-water separation and photoreactivity, respectively.
View Article and Find Full Text PDFFinite element investigation for improving chest wall reconstruction process using ceramic and polymeric implants.
Sci Rep
January 2025
Biomedical Engineering Department, Faculty of Engineering, Helwan University, Cairo, Egypt.
Car accidents, infections caused by bacteria or viruses, metastatic lesions, tumors, and malignancies are the most frequent causes of chest wall damage, leading to the removal of the affected area. After excision, artificial bone or synthetic materials are used in chest wall reconstruction to restore the skeletal structure of the chest. Chest implants have traditionally been made from metallic materials like titanium alloys due to their biocompatibility and durability.
View Article and Find Full Text PDFDevelopment and evaluation of a polymer material-based formulation for non-surgical nasolabial fold reduction.
Int J Cosmet Sci
January 2025
Makeup Products Research, Kao Corporation, Odawara, Japan.
Objective: Currently, nasolabial folds are mainly removed by invasive procedures, resulting in long-lasting changes, as non-surgical user-implementable alternatives are scarce and inefficient. For example, the use of coating films for this purpose has thus far faced substantial difficulties because such films should combine the antithetical properties of shrinkability and flexibility. Herein, we challenge this status quo by identifying a polymer that simultaneously exhibits shrinkability and flexibility and using this polymer to develop a cosmetic formulation for immediate and non-invasive nasolabial fold removal.
View Article and Find Full Text PDFSulfadiazine removal with low-cost structured nano and micro-composite hydrogel beads on moroccan clays with alginate-CMC-biochar.
J Environ Manage
January 2025
Department of Soil Science and Agricultural Chemistry, Engineering Polytechnic School, University of Santiago de Compostela, 27002, Lugo, Spain.
The primary goal of the current work was to construct pH-sensitive nano and microcomposite hydrogel beads based on alginate (AL), carboxymethyl cellulose (CMC), biochar (BC), and two Moroccan clays: Ghassoul (swelling SW) and red (not swelling NSW) nano and microhybrid. The adsorbents, SW + AL, SW + AL + BC, SW + AL + CMC, NSW + AL, NSW + AL + BC, NSW + AL + CMC, AL, and AL + CMC were prepared for the adsorption of the antibiotic sulfadiazine (SDZ). The test samples were characterized using a variety of techniques, including X-Ray Diffraction (XRD), IR spectroscopy (FT-IR), and scanning electron microscopy (SEM), with the molecular structures of the studied additives geometrically optimized using the DFT/B3LYP method and the function 6-311G(d).
View Article and Find Full Text PDFThe mechanism of alkali to inhibit the organics polymerization in improving the biodegradability of wastewater treated by heat/peroxydisulfate.
Water Res
January 2025
Yellow River Laboratory of Shanxi Province, Shanxi University, Taiyuan, 030006, PR China; The Key Laboratory of Water and Sediment Sciences (Ministry of Education), College of Environmental Sciences and Engineering, Peking University, Beijing, 100871, PR China. Electronic address:
High-temperature wastewaters can themselves activate peroxydisulfate (PDS) to remove aromatic contaminants via polymerization. This, however, may result in an insufficient carbon source for denitrification during biochemical treatment, and the formed polymers, without a proper reuse method, will be costly to handle as hazardous waste. This study demonstrates that the addition of NaOH can suppress the polymerization of aromatic contaminants, which is observed not only in simulated wastewater but also in actual coking wastewater (ACW).
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!