Synthesis of three-dimensional light fields with binary spatial light modulators.

J Opt Soc Am A Opt Image Sci Vis

Department of Electrical and Electronics Engineering, Bilkent University, TR-06800 Bilkent, Ankara, Turkey.

Published: June 2011

Computation of a binary spatial light modulator (SLM) pattern that generates a desired light field is a challenging quantization problem for which several algorithms have been proposed, mainly for far-field or Fourier plane reconstructions. We study this problem assuming that the desired light field is synthesized within a volumetric region in the non-far-field range after free space propagation from the SLM plane. We use Fresnel and Rayleigh-Sommerfeld scalar diffraction theories for propagation of light. We show that, when the desired field is confined to a sufficiently narrow region of space, the ideal gray-level complex-valued SLM pattern generating it becomes sufficiently low pass (oversampled) so it can be successfully halftoned into a binary SLM pattern by solving two decoupled real-valued constrained halftoning problems. Our simulation results indicate that, when the synthesis region is considered, the binary SLM is indistinguishable from a lower resolution full complex gray-level SLM. In our approach, free space propagation related computations are done only once at the beginning, and the rest of the computation time is spent on carrying out standard image halftoning.

Download full-text PDF

Source
http://dx.doi.org/10.1364/JOSAA.28.001211DOI Listing

Publication Analysis

Top Keywords

slm pattern
12
binary spatial
8
spatial light
8
desired light
8
light field
8
free space
8
space propagation
8
binary slm
8
light
6
slm
6

Similar Publications

Adaptation of maxillary removable partial denture frameworks fabricated with a direct digital workflow: A randomized crossover clinical trial.

J Dent

January 2025

Department of Prosthodontics, Shanghai Ninth People's Hospital, Shanghai Jiao Tong University School of Medicine; Shanghai, 200011, China; College of Stomatology, Shanghai Jiao Tong University, National Center for Stomatology, National Clinical Research Center for Oral Diseases, Shanghai Key Laboratory of Stomatology, Shanghai Research Institute of Stomatology, Shanghai, 200011, China; Department of Stomatology, Fengcheng Hospital of Fengxian District, Shanghai, 201418, China. Electronic address:

Objectives: To compare the adaptation of maxillary removable partial denture (RPD) frameworks fabricated through direct digital workflows with that of traditional cast frameworks and indirect digital frameworks.

Methods: The workflow for fabricating the digital cobalt-chromium framework encompassed intraoral scanning (IOS) using Trios 3, computer-aided survey and design, and subsequently either the lost-wax technique from a printed resin framework pattern (Framework B) or direct selective laser melting (SLM) (Framework C). The traditional cast framework (Framework A) was selected as a control.

View Article and Find Full Text PDF

This study aimed to investigate the release of metallic ions from cobalt-chromium (Co-Cr) alloys fabricated by additive manufacturing (AM) for comparison with dental casting. Co-Cr alloys were fabricated via AM using selective laser melting (SLM) and electron beam melting (EBM) in powder-bed fusion. Polished and mechanically ground specimens were prepared.

View Article and Find Full Text PDF

Deformation behavior of additive manufactured 316 L stainless steel using in situ neutron diffraction.

Sci Rep

January 2025

Research Institute of Interdisciplinary Science, School of Materials Science and Engineering, Dongguan University of Technology, Dongguan, 523808, China.

Manufacturing of metallic components using additive manufacturing technique is of great interest for the industrial applications. Here, the mechanical and microstructural responses of a 316 L stainless steel (316LSS) built by selective laser melting (SLM) with XOY and XOZ directions were revealed by performing in situ neutron diffraction tensile tests. The tensile strength of the XOY-printed samples reaches 700 MPa, while the tensile strength of the XOZ-printed samples is less than 600 MPa.

View Article and Find Full Text PDF

The ability to extinguish contextual fear in a changing environment is crucial for animal survival. Recent data support the role of the thalamic nucleus reuniens (RE) and its projections to the dorsal hippocampal CA1 area (RE→dCA1) in this process. However, it remains poorly understood how RE impacts dCA1 neurons during contextual fear extinction (CFE).

View Article and Find Full Text PDF

Natural deep eutectic solvent-based liquid phase microextraction in a 3D-Printed millifluidic flow cell for the on-line determination of thiabendazole in juice samples.

Anal Chim Acta

February 2025

Departamento de Medio Ambiente y Agronomía, INIA-CSIC, Carretera de A Coruña km. 7.5, 28040, Madrid, Spain. Electronic address:

Background: At present, 3D printing technology is becoming increasingly popular in analytical chemistry because it enables the rapid and cost-effective manufacture of sample preparation devices, particularly in flow-based operation, opening up new opportunities for the development of automated analytical methods. In parallel, the use of miniaturized methods and sustainable solvents in sample preparation is highly recommended. Accordingly, in this work, a 3D-printed millifluidic device was designed and used for the on-line natural deep eutectic solvent (NADES)-based liquid phase microextraction (LPME) coupled to a spectrofluorometer for, as a proof of concept, the determination of thiabendazole (TBZ) in fruit juice samples.

View Article and Find Full Text PDF

Want AI Summaries of new PubMed Abstracts delivered to your In-box?

Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!