Objective: To observe the growth and migration of human umbilical cord mesenchymal stem cells (hUCMSCs) on polycarbonate membrane with different pore sizes and explore the criteria of selecting optimal Transwell insert for indirect co-culture to induce the differentiation of hUCMSCs.
Methods: hUCMSCs were isolated in vitro and then expanded in culture medium. After the treatment of mitomycin C, the cells were seeded on porous membranes of 6-well-dish Transwell inserts with different pore sizes of 0.4, 3.0 and 8.0 µm respectively. After culturing for 7 days, the cells were observed and counted on the bottom of each porous membrane. Then the calculation of migration ratio was performed. The growth and migration of hUCMSCs on porous membranes were also examined under scanning electron microscope (SEM).
Results: The migration ratios of hUCMSCs on membranes of 0.4, 3.0 and 8.0 µm pore sizes were 0, 1.8% and 8.0% respectively. The migration ratio of cells on 0.4 µm pore size membrane was statistically different from that of the other two pore size groups (P < 0.01). Under SEM, a small portion of cells were growing on the bottoms of membranes and moving through the pores. But there was no cell movement through 0.4 µm pore size membrane.
Conclusions: hUCMSCs can migrate through the polycarbonate membranes of 3.0 µm and 8.0 µm pore sizes but not through the 0.4 µm one. Thus both sides of polycarbonate membrane of 0.4 µm pore size may be used for close indirect co-culture to induce the differentiation of hUCMSCs.
Download full-text PDF |
Source |
---|
Materials (Basel)
July 2024
School of Environmental Science and Engineering, Guangdong University of Technology, Guangzhou 510006, China.
By reutilizing industrial byproducts, inorganic cementitious alkali-activated materials (AAMs) contribute to reduced energy consumption and carbon dioxide (CO) emissions. In this study, coal gangue (CG) blended with ground granulated blast furnace slag (GGBFS) was used to prepare AAMs. The research focused on analyzing the effects of the GGBFS content and alkali activator (i.
View Article and Find Full Text PDFPolymers (Basel)
May 2024
Department of Fiber System Engineering, Yeungnam University, 280 Daehak-Ro, Gyeongsan 38541, Republic of Korea.
Polymer gels are cross-linked polymer networks swollen by a solvent. These cross-linked networks are interconnected to produce a three-dimensional molecular framework. It is this cross-linked network that provides solidity to the gel and helps to hold the solvent in place.
View Article and Find Full Text PDFGels
May 2024
Department of Mechanical Engineering, University of Wisconsin-Madison, Madison, WI 53706, USA.
Cardiovascular diseases (CVDs) are the number one cause of mortality among non-communicable diseases worldwide. Expanded polytetrafluoroethylene (ePTFE) is a widely used material for making artificial vascular grafts to treat CVDs; however, its application in small-diameter vascular grafts is limited by the issues of thrombosis formation and intimal hyperplasia. This paper presents a novel approach that integrates a hydrogel layer on the lumen of ePTFE vascular grafts through mechanical interlocking to efficiently facilitate endothelialization and alleviate thrombosis and restenosis problems.
View Article and Find Full Text PDFMaterials (Basel)
December 2023
School of Materials Science and Engineering, Chang'an University, Xi'an 710061, China.
To improve solid waste resource utilization and environmental sustainability, an alkali-activated material (AAM) was prepared using steel slag (SS), fly ash, blast furnace slag and alkali activators in this work. The evolutions of SS content (10-50%) and alkali equivalent (4.0-8.
View Article and Find Full Text PDFACS Omega
November 2023
Research Laboratory of Polymer Colloids and Nanomaterials, Department of Chemistry, Faculty of Science, Rajshahi University, Rajshahi 6205, Bangladesh.
Multifunctional surface-active polymeric composites are attractive materials for the adsorption of various small molecules. Herein, dual-functionalized micron-sized surface-active composite polymer particles were prepared by a three-step process for CO adsorption. First, polystyrene (PS) seed particles were prepared via the dispersion polymerization of styrene.
View Article and Find Full Text PDFEnter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!