Purpose: The objective of this study was to verify the influence of test environment on the flexural strength of dental porcelains with distinct microstructures.
Material And Methods: Disk-shaped specimens from three dental porcelains with distinct leucite content (VM: zero; CE: 12; NS: 22 vol%) were manufactured and tested for biaxial flexural strength in air and immersed in artificial saliva. The results were analyzed by means of two-way ANOVA and Tukey's test (α= 0.05).
Results: The flexural strength (MPa) obtained for ambient air and artificial saliva environments, respectively, were: 110.0 ± 16.0 and 81.5 ± 10.8 for VM; 51.9 ± 4.0 and 42.0 ± 4.7 for CE; 72.0 ± 11.5 and 63.6 ± 5.8 for NS. A numerical decrease in the mean flexural strength was observed for all groups when specimens were tested under artificial saliva; however, the difference was only statistically significant for VM.
Conclusions: The results indicate that the effect of water immersion on the flexural strength of dental porcelains varies according to their leucite content, as only the material without leucite in its microstructure (VM) showed significant strength degradation when tested under water.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.1111/j.1532-849X.2011.00711.x | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Enhanced mechanical properties and in vitro bioactivity of silicon nitride ceramics with SiO, YO, and AlO as sintering aids.
J Mech Behav Biomed Mater
January 2025
School of Materials Science and Engineering, University of Jinan, Jinan, 250022, China. Electronic address:
Silicon nitride (Si₃N₄) ceramics exhibit excellent mechanical properties and biocompatibility, making them highly suitable for biomedical applications, particularly in implants. In this study, the mechanical properties and bioactivity of Si₃N₄ ceramics with varying amounts of Y₂O₃-Al₂O₃-SiO₂ sintering aids were investigated. Increasing the sintering additive content from 4 wt% to 8 wt% substantially improved the bulk density of the ceramics, leading to notable enhancements in mechanical properties.
View Article and Find Full Text PDFFlexural Response Comparison of Nylon-Based 3D-Printed Glass Fiber Composites and Epoxy-Based Conventional Glass Fiber Composites in Cementitious and Polymer Concretes.
Polymers (Basel)
January 2025
School of Civil Engineering and Environmental Science, University of Oklahoma, 202 W Boyd St., Norman, OK 73019, USA.
With 3D printing technology, fiber-reinforced polymer composites can be printed with radical shapes and properties, resulting in varied mechanical performances. Their high strength, light weight, and corrosion resistance are already advantages that make them viable for physical civil infrastructure. It is important to understand these composites' behavior when used in concrete, as their association can impact debonding failures and overall structural performance.
View Article and Find Full Text PDFLignin Reinforcement in Polybutylene Succinate Copolymers.
Polymers (Basel)
January 2025
Department of Forest and Fire Sciences, University of Idaho, Moscow, ID 83844-1132, USA.
This study investigated the valorization of industrial lignin for producing biodegradable polybutylene succinate (PBS)-lignin copolymers. PBS was blended with varying lignin contents (0-45 wt. %) and crosslinked/grafted using dicumyl peroxide (DCP).
View Article and Find Full Text PDFThe Influence of Rice Husk Ash Incorporation on the Properties of Cement-Based Materials.
Materials (Basel)
January 2025
Green Environmental Protection Industry Co., Ltd., Guiyang 551109, China.
Rice husk ash is a kind of biomass material. Its main component is silicon dioxide, with a content of up to 80%. It has high pozzolanic activity and can react with hydroxide in cement.
View Article and Find Full Text PDFExperimental Study on Flexural Behaviour of Prefabricated Steel-Concrete Composite I-Beams Under Negative Bending Moment: Comparative Study.
Materials (Basel)
January 2025
School of Civil Engineering, Nanjing Tech University, Nanjing 211816, China.
The issues of numerous steel beam components and the tendency for deck cracking under negative bending moment zones have long been challenges faced by traditional composite I-beams with flat steel webs. This study introduces an optimized approach by modifying the structural design and material selection, specifically substituting flat steel webs with corrugated steel webs and using ultra-high-performance concrete for the deck in the negative bending moment zone. Three sets of model tests were conducted to compare and investigate the influence of deck material and web forms on the bending and crack resistance of steel-concrete composite I-beams under a negative bending moment zone.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!