Piezoelectric inkjet printing of polymers and proteins holds great promise for fabrication of miniaturized bioelectronic devices, such as biochips and biosensors. In this study, a bienzymatic glucose biosensor prototype based on poly(3,4-ethylenedioxythiophene)-poly(styrene sulfonic acid) (PEDOT-PSS), glucose oxidase (GOD), and horseradish peroxidase (HRP) was fabricated by a piezoelectric inkjet printer. An aqueous bioelectrical ink containing PEDOT-PSS, GOD, and HRP was prepared and printed on an indium-tin-oxide (ITO)-coated poly(ethylene terephthalate) (PET) film. The PEDOT-PSS/GOD/HRP sensor was covered with a cellulose acetate membrane. The use of bienzymatic sensing combined with conducting polymers via piezoelectric inkjet printing showed a synergistic effect resulting in significant amplification of the response signal. The glucose sensor reached steady-state current density within 3 s, indicating a fast response time, and exhibited a linear dose-dependent electrochemical response with high sensitivity. The overall result demonstrates that a glucose sensor with high sensitivity could be readily fabricated by a piezoelectric inkjet printing system.
Download full-text PDF |
Source |
|---|---|
| http://dx.doi.org/10.2116/analsci.27.375 | DOI Listing |
Publication Analysis
Top Keywords
Similar Publications
Inkjet-based facile fabrication of a copper ferrocyanide-embedded magnetic alginate microadsorbent for highly enhanced cesium removal.
Carbohydr Polym
January 2025
Decommissioning Technology Research Division, Korea Atomic Energy Research Institute, 989-111 Daedukdaero, Yuseong, Daejeon 34057, Republic of Korea.
For the first time, simple and facile fabrication of a magnetic alginate microadsorbent via piezoelectric inkjet technology was developed for the selective removal of Cs via magnetic separation. Through the ejection of an alginate solution containing potassium ferrocyanide and magnetic nanoparticles (MNPs) into a Cu solution via an inkjet device, the fabrication of a copper ferrocyanide-embedded magnetic alginate microadsorbent (CuFC-MAM) with an average size of 39.38 μm was easily achieved in a one-pot fabrication process; here, the Cu ions acted as both a cross-linker for the gelation of alginate and a Cu source for the in situ synthesis of CuFC with potassium ferrocyanide.
View Article and Find Full Text PDFFabrication of Engineered Drug-Polymer Composite Particles via Piezoelectric Inkjet Technique for Floating Drug Delivery Systems.
Langmuir
December 2024
Department of Chemical Engineering (BK21 FOUR Integrated Engineering Program), Kyung Hee University, Yongin 17104, South Korea.
This study presents a simple approach for fabricating low-density drug-polymer amorphous solid dispersions (ASDs) using a piezoelectric inkjet method, demonstrating potential applications for floating drug delivery systems (FDDS). By adjusting the ratio of two polymers, polylactic acid, and Eudragit RLPO, the floatability and drug release rate of the drug-polymer ASD particles can be easily manipulated. Kinetic model analyses have been conducted to interpret the drug release mechanism.
View Article and Find Full Text PDFResidual Vibration Suppression of Piezoelectric Inkjet Printing Based on Particle Swarm Optimization Algorithm.
Micromachines (Basel)
September 2024
State Key Laboratory of Robotics, Shenyang Institute of Automation, Chinese Academy of Sciences, Shenyang 110016, China.
Piezoelectric inkjet printing technology, known for its high precision and cost-effectiveness, has found extensive applications in various fields. However, the issue of residual vibration significantly limits its printing quality and efficiency. This paper presents a method for suppressing residual vibration based on the particle swarm optimization (PSO) algorithm.
View Article and Find Full Text PDFEfficient Creation of Jettability Diagrams Using Active Machine Learning.
3D Print Addit Manuf
August 2024
Polymer Program, Institute of Materials Science, University of Connecticut, Storrs, Connecticut, USA.
The ability to jet a wide variety of materials consistently from print heads remains a key technical challenge for inkjet-based additive manufacturing processes. Drop watching is the most direct method for testing new inks and print head designs but such experiments are also resource consuming. In this work, a data-efficient machine learning technique called active learning is used to construct detailed jettability diagrams that identify complex regions corresponding to "," "," and "," rather than only individually sampled points.
View Article and Find Full Text PDFPhosphoramide Hydrogels as Biodegradable Matrices for Inkjet Printing and Their Nano-Hydroxyapatite Composites.
ACS Appl Mater Interfaces
October 2024
Institute of Polymer Chemistry, Johannes Kepler University, Linz 4040, Austria.
Inkjet printing is a leading technology in the biofabrication of three-dimensional biomaterials, offering digital, noncontact deposition with micron-level precision. Among these materials, hydroxyapatite is widely recognized for its use in bone tissue engineering. However, most hydroxyapatite-laden inks are unsuitable for inkjet printing.
View Article and Find Full Text PDFWant AI Summaries of new PubMed Abstracts delivered to your In-box?
Enter search terms and have AI summaries delivered each week - change queries or unsubscribe any time!